Jump to content
SAU Community

Recommended Posts

The only difference witht he R33 S2 is it uses 1 earth for both the signal and 12v feed.

Grab a multimeter and find out which one is which, its easy.

The z32 afm wiring guide I did has been corrupted, I upload a new uncorrupted version however the forum still corrupts it. :(

With regards to the plug I popped down to the local U-Pull It parts wreckers and grabbed a plug from a VL Commodore, they are the same as the Z32 plug.

Link to comment
https://www.sau.com.au/forums/topic/84179-tomei-z32-plugs/#findComment-1524289
Share on other sites

From what I can see on the loom i have lying around, the R31 (aussie) is also the same 4pin square plug.. so yeah, doesn't matter if its off a VL or R31 (prolly not pintara though as they have a different afm from what i remember)

Link to comment
https://www.sau.com.au/forums/topic/84179-tomei-z32-plugs/#findComment-1525670
Share on other sites

yes i use flux cored solder also and it works fine...flux pen thats like oxy brazing and having to dip the wire in the flux before welding...messy :P

Thanks for the offer crazy_boy but i should be fine on this one...just wasnt sure what the go was with the wires but i can use a multimeter to work out earth and 12v supply cheers.

Link to comment
https://www.sau.com.au/forums/topic/84179-tomei-z32-plugs/#findComment-1525710
Share on other sites

The flux pen is nothing like oxy brazing. :P

The flux pen is a pen so you simply 'draw' on both wires, so its not messy.

Pool the solder on the soldering iron touch the wires and because the wires have the flux on them its like the wires suck the solder from the soldering iron.

I noticed the R31 afm plug was the same also.

Link to comment
https://www.sau.com.au/forums/topic/84179-tomei-z32-plugs/#findComment-1525818
Share on other sites

I was refering to the difference in processes...not the actual flux for wire and flux for brazing...my bad again...i assumed you would understand it from my view...i really should explain things more clearly.

-like heating up job then wire and dipping wire in flux and then brazing

-applying your flux pen to the wire then pooling the solder and letting it attach itself to the flux coated wire. both manual processes

-while just pooling solder with flux in it and letting it attach to the wire. more simpler process...but each to their own!

Link to comment
https://www.sau.com.au/forums/topic/84179-tomei-z32-plugs/#findComment-1526077
Share on other sites

This is the solder I use. It has a resin core? Is that the flux?

Solder

I had some other stuff that was a little thicker and didn't melt to well with my cool soldering iron. It was supposed to have flux in it.

I had problems with the solder staying on the soldering iron and not transfering to the wire. The wire would end up having its insulation melted as the only way to get the solder on to the wire was to heat the sucker up. Even then it was still difficult.

Link to comment
https://www.sau.com.au/forums/topic/84179-tomei-z32-plugs/#findComment-1526899
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...