Jump to content
SAU Community

Recommended Posts

Hmmm 41 pages later and I've read 18x9 +30 will fit on the fronts of a R33 GTST25 and some say they won't.

I'm actully more worried it'll hit the upper arm on the inside than the guards as this one is sitting on blisten shocks with king springs. Back should be OK, got 9" on there now with +38

i have the exact same size wheels and yeah, they clear the suspension by a bee's dick. any wider than the 235/40/18 i have on there atm and i reckon it'd foul

Thanks! and btw, nice avatar Hekt1k (van buuren ftw!)

it will fit pending rim design, my 18x9 +30 didnt fit without spacers but they were deep dish rims. GTR wheels will fit no problem and u wont hit any suspension parts at all. ive got 18x9.5 +15 and clears no problems what kinda of rims are u going for?

it will fit pending rim design, my 18x9 +30 didnt fit without spacers but they were deep dish rims. GTR wheels will fit no problem and u wont hit any suspension parts at all. ive got 18x9.5 +15 and clears no problems what kinda of rims are u going for?

*cough* rota g-force *cough* got them really cheap XD;; now just need to fix car (not dish rims very...not dish lol)

there is seriously fk all clearance in there Hamish, does your wheel alignment give more room or do you just deal with it?

i'm running a little bit of positive castor and the fronts don't have much camber (basically a standard centreline setup).

no scrubbing at all... but as you said, fuck all clearance...

rota g force will suit your purpose fine plus everyone needs thrash rims i got piaa rozza's which are uglier then ox arse but they serve their purpose.

hamish - fk all clearance is plenty you only have to start worrying when you have below NO clearence cos everyone loves a bit of scrubbing :) oh wait maybe thats just us westies

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...