Jump to content
SAU Community

Recommended Posts

hey guys atm i am working to make 200rwkw after my last dyno of a shit 140rwkw due to poor tune and lack of a few things

Mods last dyno

Gts-t R33 rb25det

Link Plug in replacement ECU tunes by poor shop at 7psi on 95oct fuel

PWR INTERCOOLER

K & N POD

Trust Catback

Now my new plan is mod then retune it at MRT in Sydney On 12psi and get near 200rwkw

New Mods that i hope help me get to 200rwkw

Dump and front Pipe Twin set up off BOS

Hi flow Catco cat

PLUMB BACK BLOW OFF VALVE caust stock one isn't working right Flutters on 7psi

loud ( NOT sure on what brand anyone know any good ones for Plumb backs

custom 3" pipe intake from turbo to Pod without AFM due to link computer

last of all thinking Cam Gears but will they heap on stock cams

anyone know if cam gears will gain more power r they worth the money also what brand

OS GIKEN or TOMEI

thinking about new Timing beat too while cam gears r off

what u guys think

Edited by scottman
Link to comment
https://www.sau.com.au/forums/topic/84593-adjustable-cam-gears-on-stock-cams/
Share on other sites

Those mods with a good tune should push you to that figure, or very close to it.

But if you looked in the Quick Ref guide at the top of this forum you would have seen the following threads

Ex. Cam Gear: http://www.skylinesaustralia.com/forums/sh...41&page=1&pp=25

Dump Pipe: http://www.skylinesaustralia.com/forums/sh...ead.php?t=10567

btw, 140kw is what you would expect for a near stock Skyline. That must have been a really really bad tune..

Those mods with a good tune should push you to that figure, or very close to it.

But if you looked in the Quick Ref guide at the top of this forum you would have seen the following threads

Ex. Cam Gear: http://www.skylinesaustralia.com/forums/sh...41&page=1&pp=25

Dump Pipe: http://www.skylinesaustralia.com/forums/sh...ead.php?t=10567

btw, 140kw is what you would expect for a near stock Skyline. That must have been a really really bad tune..

I know 140rwkw is low but i beat one of my mates with a gts-t with a full exhaust so i am guessing maybe the dyno was just out been just beaten by a 180sx and onces by a gts-t with least mods then mine he was a better driver

I am Hoping its just the Tune Mrt will work out whats holding my Power back

Tony,

Cmon you should know better ;) Those are the "Revision 1" HKS gears. The "Rev. 2" gears -- which use duralumin -- don't appear to have the same problems.

Edit: I'd still look at getting the Tomei gears as part of the camshaft + camgear packages they do.

LW.

Cam gears will make some difference, but not 60+ kw. (AFAIK, all they do is move the power band, they don't necessarily make more power).

I suspect it's the tune. I'm running a RB25DET on a Wolf 3D. It has VVT, and is otherwise stock. It was tuned at 10psi on 95 octane, and pushes 180 kW out through 4 wheels (R32 GTS4). Granted it does also have a "hi-flo" cat and a dump pipe, but still runs the factory air box and filter.

Hey whats the deal, is there something freaky about my car cause i got it dynoed with minor mods (see sig) and even at 7psi it was pulling 169rwkw, and was 186rwkw @ 10psi.

Was dynoed at unigroup, i would have thought scottmans would have been more powerful...

Must be UBER dodgy tune

i have no idea why its only 140rwkw i am hoping to try and fix it hoping its just the tune

other things it cound be is Fuel Pump or injectors or something MRT will find out hoping to fix it :P

still i own lots of shit with 140rwkw :blink:

I thought it was shited so i went and raced my mates Gts-t r33 with a Full Exhaust and BOV and i beat him so i have no Idea maybe it was the dyno

If you want to try adjusting the inlet gear whilst keeping the use of your VVT, PM me.

I've got a little invention that may just help you out.

Yo bass.Have you made some for r33 now.Or is this a trick that you have up your sleve.

I have the newer HKS gear and its fine....

Didnt gain anything at all... Just got a few more km's per tank and smoothed out the top end.... No jerky action inbetween 6-7000k....

AND more importantlly i got FLAMES>>>>> LOL

Scottman, what dyno was it on ? The dynologs read alot lower than the DynoDynamics ones (most common).

I just had car on dyno yesterday to retune, and all i could get was 145 rwkw's (Dynolog)

(was tuning it myself)

Now bear in mind this is S1 R33 GTST, std turbo

3" turbo back, and i just put a 4" magic cat in (which does work well by the way , 4 gas analyser confirmed)

I have a plug in LINK. No AFM (3" SS Pipe to pod)

Carbon cleaned it too.

R34 GTT cooler

And just fixxed the coil probs with a mates 32 GTR coils borrowed till the splitfires arrive... also new BKR6EIX iridiums (.8mm std gap). After last tune the coils shat themselves , siliconed them to get by, but power was flat...

Also fitted a MV auto shift kit.

Its been a busy 2 weeks !

Heading out to drags again tonight to see how it goes...

Two weeks ago with it feeling flat it ran a 14.6 @ 95.3 mph So i hope i can get a 13 tonight ... time will tell.

I think you should go out to the strip and just see what mph your getting ......that will be a better indication of how well the cars going.... as your dyno may read low as well.

Gary

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...