Jump to content
SAU Community

Recommended Posts

I just had my car tuned...

R33 S1.5

Trust Front Mount

Full Exhaust

Nismo Fuel Pump

HKS 2535

PFC

At 14psi it pulled 244rwkw and is amazing to drive!!!

My new best friend will be the local servo i think!

I thought it would have terrible traction with the crap 326's but it doesnt! it actually pulls very hard with fantastic grip in a straight line. Of course its quiet easy to smoke the tyres through 2nd but the power delivery is so smooth it usually just grabs and goes!!!

I would recommend this setup to anyone for street use! more power everywhere!!!

Cheers!

Edited by silva33
Link to comment
https://www.sau.com.au/forums/topic/85009-hks-2535-results/
Share on other sites

Ill have to take a photo of the graph with my phone and post it up...

INASNT; i bought the Apexi N1 off your friend and had them install it yesterday....

It is pretty loud but im sure ill get used to it...

Only mods are those posted... Stock injectors, no FPR or Z32.. max knock was around 30 on the PFC.. i dunno about the max duty of the injectors, i forgot to ask..

I was told it was making about 150ish rwkw by 3000 rpm and max power at about 6,500 rpm. (ill have to check it on the dyno graph though)

boost held to 13psi (from 14psi) till redline which i was not expecting..

Edited by silva33
Link to comment
https://www.sau.com.au/forums/topic/85009-hks-2535-results/#findComment-1539896
Share on other sites

it did cost u big bucks??? hahaha

not really...

in this case, you get what you pay for... if you saw how stock my car looks you would know what i mean and considering i have been burnt in the past by previous tuners im more than happy to pay a little more for the service and quality...

Edited by silva33
Link to comment
https://www.sau.com.au/forums/topic/85009-hks-2535-results/#findComment-1539943
Share on other sites

i just got my power fc tuned with my 2535 bolted up. Ended up with 231.1rwkw at 13-14psi. i do have a z32 afm and a nismo fpr and i'm very happy with the results. max knock is 11 and injectors get to max duty of 84% as far as ive seen. Like silvar33 my exhaust is a little restrictive. My tune feels very strong on boost but safe. Chasers tuned the car and they said on other dynos it might squeeze out a few more kw's but im happy with the performance of the car.

For those people who believe that a HKS turbo is a waste of money im happy to take them for a drive and show them the difference. No comparison compared to standard

Link to comment
https://www.sau.com.au/forums/topic/85009-hks-2535-results/#findComment-1540132
Share on other sites

Sounds good reflex..

It would be good to compare the two cars it see how the tunes are different becuase if anything yours should be smoother than mine with the Z32 AFM

yeah mine is really smooth, i thought it be a bit laggy but its pretty good. im making full boost at 3000-3200rpm. oh yeah my traction issues arent to bad, got brand new tyres tho.

ill put up my graph tommorrow arvo, there isnt any significant dips in my curve and theres no spiking

Edited by reflex
Link to comment
https://www.sau.com.au/forums/topic/85009-hks-2535-results/#findComment-1540546
Share on other sites

i just got my power fc tuned with my 2535 bolted up. Ended up with 231.1rwkw at 13-14psi. i do have a z32 afm and a nismo fpr and i'm very happy with the results. max knock is 11 and injectors get to max duty of 84% as far as ive seen. Like silvar33 my exhaust is a little restrictive. My tune feels very strong on boost but safe. Chasers tuned the car and they said on other dynos it might squeeze out a few more kw's but im happy with the performance of the car.

For those people who believe that a HKS turbo is a waste of money im happy to take them for a drive and show them the difference. No comparison compared to standard

hi reflex,

what injectors are you using?

Link to comment
https://www.sau.com.au/forums/topic/85009-hks-2535-results/#findComment-1540667
Share on other sites

this is what ive come up with.

i bought my series 1 r33 18 months ago with basics

-3 inch exhaust

-boost controller

-pod filter

-rims

-bov

-fuel pump

-surge tank

-turbo timer

since then ive bought

-intercooler $400

-piping $250

-fpr $150

-power fc $1000

-hks 2535 $1300 exchange for standard

-z32 afm $220

-tuning $500

TOTAL - $3820

everything else is standard though

ive achieved 231 rwkw relatively cheaply, ive wasted plenty of money other crap like body kit, sound system, clearing defects, servicing etc.

for anyone out there looking to achieve strong, safe reliable results this is one option that you should look into.

this website is great for finding second hand parts in good condition

by the way my engine bay looks completely stock except for red rocker covers

Link to comment
https://www.sau.com.au/forums/topic/85009-hks-2535-results/#findComment-1540706
Share on other sites

Dyno graph pls !

Sounds almost too good to be true dude ! with stock injectors no FPR or AFM !

He said he will post it up so give him a chance buddy <_<

Impressive power figure you and reflex have there.

Hope i get something similar out of the lil ol Rb20 of mine :P

Cheers B

Link to comment
https://www.sau.com.au/forums/topic/85009-hks-2535-results/#findComment-1540717
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...