Jump to content
SAU Community

Recommended Posts

The best track day you will go to.

Professional in car and pit race driver instruction.

Professional transponder computerised accurate timing.

Biggest collection of GTS-T's and GTRs as well as other cars including one fast zed.

Crowd of fellow enthusiasts.

Drifting segments.

Pro Photographers.

Events and action caller.

$195 to enter. South Circuit.

bforan.jpg

Link to comment
https://www.sau.com.au/forums/topic/86034-uas-track-day-sunday-25th-septemeber/
Share on other sites

  • 2 weeks later...
GTR Jason, I thought the guy dissapeared? whats his username on here?

guys can I attend even tho I have an EPA defect atm?

You should be fine, most cars on race tracks will never pass EPA inspection(for road use)

Edited by Flaps

John,

Whats the track sheduale look like, ie what drive type and times.

Whats the count how may cars do you have?

Remember, you only have 4 days to not have your boat ready.

Hmm I can already taste that bottle of 707 now.

GTR Jason was my mechnaic for a while on the R32... then he dissapeared and some dodgyass holden mechianic that bought his workshop quoted me $3000 to fix a little problem that I later found was just a speedo needle sticking out of the instrument cluster and controlled everything on the car includign speed, hicas, power steering etc.!!!! Free 5 minute fix against $3000 that would not fix the problem and take forever!!!!!

Not a lot of SAU people there but a great day even though I was only there for 3 sessions.

How did Caroline go in the Silver Zed? Did anyone notice the tyres she had on? :(

Adrian



  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...