Jump to content
SAU Community

Recommended Posts

I have just got my intercooler fitted on my R32 Gts-T.

Getting it back, i noticed in no way did it "feel" like it had anywhere near as much torque, and really feels like its struggling. Quite laggy, no response b4 3k rpm where it was hitting full boost @2800 previosuly. Previosuly the car was running 12psi with a side mount, with a 3inch turbo back system-no mufflers, just a cannon. Now im not quite sure wat it is running as far a pressure, but certainly has dropped, used to go somewhere almost to the 7 on the stock guage now a touch further back ....have an upgraded fuel pump, and k&n filter with a stock box. Will attaching my boostcontroller assist in removing this lack of power...? In addidition to this i was surprised when me and a mate (200SX relatively stock (pod, touch of boost)) on the freeway, both in third doing legal speeds of course :D , both gassed it and it couldnt even pull more than a car away...with the above sorts of mods in comparison to relatively stocker S14, i would expect a little more from the RB.... any thoughts are greatly appreciated.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/86368-intercooler-fitted/
Share on other sites

Hey, a fairly reputable workshop in adelaide fitted it. Graham West. Running rich-hmmm possibly dunno tho cant really tell until u get it all hooked up.. but i am wanting to get a remapp of the stock comp. Leaks.... what is the best way to tell? Before when cold the car used to do this whistling thing (veryslight) until it warmed up....now it does the same thing to the same extent...soo?? How hot/cold should the pipes be feeling on the cooler just above the engine etc??

Cheers

It was the full Greddy V-Spl kit....all the piping included...brand new!

but yeah it actually feels like its lost power instead of gained it!....and power comes on much later to make things worse

Anything anyone can recommend?

if you just fitted a fmic to your system and made no other changes then yeah i'd expect more of a lag or delay in response as you have to pressurize all the piping and the larger core now. make do some exhaust changes at the same time? split 3" dump or something?

if you already have exhaust done.

get a boost controller and boost gauge.

get to a dyno place and have them increase the boost to say 12 psi while it's on the dyno.

then you can see if the car is running rich or lean and know that the increased boost is at a safe limit.

and you're surprised that you couldn't pull away from an S14?

why?

they are lighter and have more torque.

You will get slightly more throttle lag when installing a larger front mount and I found that if your running standard ecu you will run really rich thus will rob your power significantly. If there is a leak in the cooler pipes you will hear it, so my guess is that you need to get it tuned. Might be a good idea to get a boost guage to tell you exactly what you running so you can moniter boost aswell, stock boost guage is shite. You really shouldnt be losing power though with the denser air going into the inlet. :)

off topic but has anyone actually seen the stock guage to be inaccurate and give wrong results? i dont see the need for an aftermarket guage

Im sure that its accurate, but there isnt any way of distinguishing small increments in boost. eg my Blitz boost guage goes like 0, 0.1,0.2,0.3,0.4,0.5,0.6 bar etc the stocky goes -7x100mmHG, 0, +7x100mmHG, it fine to guess but can you tell the difference between 12psi and 13psi? If your running a stock turbo it might mean the diiference between blowing it up or extending its life. For the price of $60 to $160 its small invetment.

Plus they look good hehe

post-14246-1125888021.jpg

cost effective method would be to just get a digital boost controller, as it will show the pressure in digital reading, negating the need for an aftermarket guage

What if you have a bleed valve? Personal preference I guess, I find it easier to read than digital.

Add boost. R32's don't have the rich/retard thing like r33's so it's worth doing. Put in 12-13 psi, check it for ping, if no ping advance the static timing to 16 or 17, check it again. It makes for a fun car. Don't run more boost than this for a couple of reasons, 1) the turbo is out of puff and really only heats the air, 2) hot air means ping.

The stock boost gauge is a slow piece of crap btw, it takes a long time to start registering changes. Get an aftermarket, they're cheap enough and good insurance.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...