Jump to content
SAU Community

Recommended Posts

Hey guys,

I got a prob with my front passenger rim on my 33. i thought the tyre somewhere had a leak as the tyre leaks air over about a month b4 i need to constantly reinflate it, so im always topping it up. i got it all checked out thinking it was the rubber, but they found a hairline crack in the actual rim.

I have 18" ROH Drift R's on the car, and i dont really want to replace that 1 rim which will prob cost 500 bucks, but it looks like i have no choice, it must be fixed or it will always continue to leak.

Is it possible to like get a tube put in just that wheel to fix it, as these type of wheels are tubeless..if thats the case id much rather pay 40 bucks than 500.

any advice would be appreciated

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/
Share on other sites

you can get it tubed at your local tyre place should be no dramas however i would be concerned of the safety of the rim itself if its cracked.

it could be unsafe and expand more or crack more at high speeds, that would be fatal, especially on the front

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/#findComment-1565224
Share on other sites

um iam pretty shore they dont make tubes for 16-17-18s coz they low profile, could be wrong about 16s but others iam shore off, just get some reall good glue n tank the tyre look 4 where air is comeing out n GLUE it, but i would fix or get new 1 if u wont i can get u these rim most likly.

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/#findComment-1569968
Share on other sites

i would advise against the tube idea even if you can find one for your wheel as they are not the safest things going around (excuse the punt)

as someone suggested best thing is to get it repaired by wheel repairers.

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/#findComment-1570307
Share on other sites

I got the wheel checked out at an ally repairer, the wheel is f***ed. the crack is too close to where the spoke meets the inner part of the rim so the only option is a new rim. but the rim is $280 so its not too bad..i was expecting them to be around 400-500 per rim.

And yes im still getting the 34. had it checked out and all looks good.

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/#findComment-1576025
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hard to say, just pop the rocker covers off and have a look if you think it's cammed. You probably need to replace the valve cover gasket/half moons anyways.
    • From my youth: GTi-R clutch change is a massive pain. The gearboxes are fragile? But the car is super cool and I want one 😢 
    • Remember this is 1988 tech.
    • Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
×
×
  • Create New...