Jump to content
SAU Community

Powerfc In Auto R34 Gtt

Abo Bob

By Abo Bob,
in Engines & Forced Induction

 Share

Recommended Posts

Abo Bob Grand Master

Abo Bob

Posted
Posted

The R34 GTT ECU and TCU are contained in the one unit.

I have had my transmission rebuilt and I'm told it can handle 300rwkw without needing the soft landing, ie timing drop, that the stock ECU does.

I was reading Sydneykid's thread on the SITC and thought perhaps I need a piggyback ECU that goes between the stock ECU and the coils.

Which ones do this? Unichip?

Then I had a brain wave.

What if I get a PFC and plug most of the wires into it so it can run the engine. Then run extensions to the signal wires that the TCU requires to run the auto transmission over to the stock ECU so that both the PFC and the stock ECU will be receiving input from all the sensors.

Any wires that are sending information from the stock ECU to the engine will not be connected. The wires that send information the transmsission would be connected.

What do you all think?

Link to comment
https://www.sau.com.au/forums/topic/86992-powerfc-in-auto-r34-gtt/
Share on other sites
ed Grand Master

ed

Posted
Posted (edited)

adam, the pfc will run an auto car. The only problem is flaring on the shifts as it doesn't pull back timing for the shifts.

I can't see your theory working but I am waiting to be proved wrong. :)

Why can't you just wait for darkhalf's boards? hehe

Edited by ed
predator Grand Master

predator

Posted
Posted

I did think there shouldn't be any clear reason with enough wiring to run both ECU's simultaneously it shouldn't work??

I haven't seen any previous mention of this on here..

http://www.powertraincontrolsolutions.com/content-4.html

Any reason why?? other than the ~$1000 pricetag of course. I guess for R34 they have a slightly different version of the autos.

Abo Bob Grand Master

Abo Bob

Posted
  • Author
Posted
adam, the pfc will run an auto car. The only problem is flaring on the shifts as it doesn't pull back timing for the shifts.

I can't see your theory working but I am waiting to be proved wrong.  :)

Why can't you just wait for darkhalf's boards? hehe

The shifts wont flare on my car because my gears changes are too tight.

I know there is the odd R33 with PFC but don't R33's have a separate controller for the auto? What happens if I press the button on my steering wheel with a PFC and nothing else? Probably nothing cos it wont be connected to anything.

  • 9 years later...
zoomzoom Mentor

zoomzoom

Posted
Posted

Adaptronic 440. It has a lot of integrated features which can save you money, ie boost control, serial input for a wideband, programmable outputs, plus some neat adaptive tuning features, ie with a wideband it can automatically alter a fuel map (though best results are done manually). Plus theres a flex fuel functionality if you're interested in e85.

Just be mindful that you're starting from scratch with ignition and fuel maps, so the learning curve is very steep. Although there are base maps available, they arent very good. You'll need to learn how to tune yourself, even in conjunction with a tuner.

GTSBoy Grand Master

GTSBoy

Posted
Posted

i was looking at other options to have a true 4" intake without going down to 3" for the z32, or not having to run a z32 in the cooler piping thats all

Nistune is not limited to running Z32 AFM. You can install an R35 AFM sensor into a 1000mm drainpipe if you want and set Nistune up to run with that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • DraftySquash
      Looking for someone with a R34 front bar

      By DraftySquash · Posted

      Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Dose Pipe Sutututu
      new 1.5 LSD issues/concerns

      By Dose Pipe Sutututu · Posted

      Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...