Jump to content
SAU Community

Recommended Posts

  • Replies 86
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Has anyone actually received any items from this guy I was ment to receive seatbelts yesterday at the latest after waiting for about 4 weeks for them to arrive he tells me he only sent them on the 9th and was ment to give me a tracking number which he currently doesn't have access too because hes not at home it just seems like one excuse after the other and im a little suss.. so plz pm me or post if you've actually gotten something off this guy plz so i can put my mind at ez

Link to comment
https://www.sau.com.au/forums/topic/88128-r32-parts/page/4/#findComment-1639314
Share on other sites

pm sent,  still waiting for my boot carpet to arrive, paid for at the beginning of this post.

boot carpet - express post sq7915164

seatbelts - express post - mq7311040

vents - express post - mq7311039

found them all in works mail room unsent, have been sent now!

Link to comment
https://www.sau.com.au/forums/topic/88128-r32-parts/page/4/#findComment-1639570
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...