Jump to content
SAU Community

Recommended Posts

Originally posted by Sneeza

see - thats what everyone says "you couldn't handle it" But I know I could. I have taught swimming and bronze medallion and I love the first aid stuff. I see stuff in SES..... I know I handle it

go for it then

but keep the IT job while u do the training.

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by Pva_Glue

uummm no troy I dont eat dog or cat or any animal that you think I would be...

but then again this was last year Vet anatomy &physiology! :(

People I WARN YOU THIS IS VERY GRAPHICAL IMAGE YOU GOING TO BE OPEINGN!!! SO BE WARNNED!!!

cheers

JOe

joes just cutting up his dinner

Originally posted by Sneeza

yeah thats another thing - company loyality. Like they invest a bit of money into sending me on courses and stuff and could I do that to them - just leave? Perth is a small place and if I wanted to go back to IT... word would have gotten around

not that small a place, seeing bunnings is a private sector its less likely that rumours will be spread about u.

governement on the otherhand yes they'd know everything about u before the interview.

Guest
This topic is now closed to further replies.



  • Latest Posts

    • The frontend wouldn't go low enough because the coilover was max low and the upper control arm would collapse into itself and potentially bottom out in the strut tower. I made a brace and cut off the kingpin and then moved the upright down 1.25" and welded. i still have to finish but this gives an idea. Now I can have a normal 3.25" of shock travel and things aren't binding. I'm also dropping the lower arm and tie rod 1.25".
    • Motor and body mockup. Wheel fitment and ride height not set. Last pic shows front ride height after modifying the front uprights to make a 1.25" drop spindle.
    • Here's Logans Silvia with R32 Drivetrain, mine will be slightly lower (more angle). He was constantly blowing the RH axles at around 16deg. I want to avoid this.    
    • Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
×
×
  • Create New...