Jump to content
SAU Community

Whoretown WA

skyzerr33

By skyzerr33,
in Western Australia

 Share

Recommended Posts

Pva_Glue Grand Master

Pva_Glue

Posted
Posted
Originally posted by darK

yea.. i was kiddin with the "kun"..

yea.. i know he's korean.. i was trying to speak german.. but i forgot it all ;)

lol

hahahah good try...

should say more like "An nyoung Ha Sae Yo!" :)

and also "kun" or "con" in Koean means Sir ;):(

Jap and Korean have similar sound words :(

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Popular Days

Top Posters In This Topic

Popular Days

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by macka

Mike dont wreck your car u only just got it going properly!!

I agree , don't **** with it until you are going to do some wholesale changes like aftermarket terbs etc.

Remember the ones at the track have no aircond , don't have to idle well , are running no airflow meters , hence no recirculating BOV's ... etc etc.

cheers

Ken

Nizmo Grand Master

Nizmo

Posted
Posted
Originally posted by gtrken

Remember the ones at the track have no aircond , don't have to idle well , are running no airflow meters , hence no recirculating BOV's ... etc etc.

cheers

Ken

Sounds like my car :(

Micko Veteran

Micko

Posted
Posted
Originally posted by gtrken

I agree , don't **** with it until you are going to do some wholesale changes like aftermarket terbs etc.

Remember the ones at the track have no aircond , don't have to idle well , are running no airflow meters , hence no recirculating BOV's ... etc etc.

cheers

Ken

Hmmm...once again the voice of reason rings loud in my ears.

Thanks Ken - just want a clean looking engine bay & less pipework so that I have a chance of understanding what is going to what:uh-huh:

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Nizmo

*sigh* but front and rear have been swapped I watched them do it!

Ahh yes , I know that , you told me last night. ( remember , I stalk you Niz and hang of every word you say.... )

Did the problem get worse after they swapped them and why did they swap them in the first place.

I am not having a go at you but as I also mentioned last night , one of the major probs with doing correct diagnosis is knowing ALL the symptoms and what was happening leading up to the prob.

cheers

Ken

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
    • Murray_Calavera
      Jacks that fit under GTR lips that can reach the subframe?

      By Murray_Calavera · Posted

      I have too much trauma from every skyline I've ever seen having crushed jack points/pinch welds lol.    Yep, works 100%, it's what I use when I'm using the quick jack. Don't know why I can't also bring myself to do the same thing when I'm using a jack. I blame the skyline PTSD. 
×
×
  • Create New...