Jump to content
SAU Community

Whoretown WA

skyzerr33

By skyzerr33,
in Western Australia

 Share

Recommended Posts

Micko Veteran

Micko

Posted
Posted

See ya Kyles:)

Yep - we are sure that it never did it before Ken.

It started last night - we went from your house to the servo near me, he filled up & then it started playing up. Is there any chance that it could be associated with the pcv as aside from the immobilser, that is the only thing that was altered on the car recently?

Could be because the wing isn't on it any more:bahaha:

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Popular Days

Top Posters In This Topic

Popular Days

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Micko

See ya Kyles:)

Yep - we are sure that it never did it before Ken.

It started last night - we went from your house to the servo near me, he filled up & then it started playing up. Is there any chance that it could be associated with the pcv as aside from the immobilser, that is the only thing that was altered on the car recently?

Could be because the wing isn't on it any more:bahaha:

Nah , car is back to the same as when I ran it. ie. pcv blocked , breather cleaner on.

Only change is the immobiliser. Are you sure all the wiring has been put back to std when you pulled the immobiliser

cheers

ken

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by GTS-t VSPEC

Damn, That was a pathetic Saturday night of whoring, took me 2mins to read back:p

Hope the cruise went ok:D

Ahh yes but some off us have a life and DO actually go out .

Think a lot might have cruised with epoch and I did the brownie point thing and went to La Cascade in Nedlands with the missus.

* Thinks , would rather be out cruising*:)

Seeya Paully and get off this damn puter and go on holiday:D

Cheers

Ken

Nizmo Grand Master

Nizmo

Posted
Posted

hehe hey Ken .... me n Liz got into mischeif last night :D

We stumbled upon the South Australian Football Club and the club president was trying to pimp his guys out to me ....."What about this guy? hmmm do u like italians? ........ can i introduce u too? ..... Cmon just tell me which one you like and i'll see what i can do"

Had such a funny night ..... i think me n Liz really needed a night liek that :uh-huh: certainly got our minds off things! :)

Nizmo Grand Master

Nizmo

Posted
Posted

anyway must go pick up mel for lunch in freo .... Liz maybe i should go bang on room 1033 and see if they are up yet haha i would imaginethere would be a lot of hangovers this morning!!

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
    • Murray_Calavera
      Jacks that fit under GTR lips that can reach the subframe?

      By Murray_Calavera · Posted

      I have too much trauma from every skyline I've ever seen having crushed jack points/pinch welds lol.    Yep, works 100%, it's what I use when I'm using the quick jack. Don't know why I can't also bring myself to do the same thing when I'm using a jack. I blame the skyline PTSD. 
×
×
  • Create New...