Jump to content
SAU Community

Recommended Posts

Originally posted by Sneeza

Kym - hahahaha I had to make myself laugh..... I have had a bad week

Ken - nah came home... rings are gone.... things up in the air.... I dont give a shit anymore. i think I might go to confession this week hahaha

well, you're doing a good job making me piss my pants..!

the "rings" are gone being the wedding rings ? am i hearing correctly ?

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by gtrken

Hey , stop ruining the dirty ambience:D  

Engine is together, goes back in tomorrow and hopefully will be running it in up and down the freeway thursday or friday night.

Cheers

Ken

Does that mean you are going on the cruise this Sat night?

Originally posted by Sneeza

Kym - hahahaha I had to make myself laugh..... I have had a bad week

Ken - nah came home... rings are gone.... things up in the air.... I dont give a shit anymore. i think I might go to confession this week hahaha

Go to confession??

Is that like the local pub ??:D

Cheers

Ken

Originally posted by Micko

Does that mean you are going on the cruise this Sat night?

No cos the Autronics won't be in so severely limited to revs and boost.

And if Simon is going , I wouldn't be able to control myself if we lined up.

He is starting to annoy me with the

* ohh I beat you and Brett * syndrome.

Cheers

Ken

Originally posted by Sneeza

mmm anyway guys... I have run out of dirty things to say.....  

Me and my plucked chicken are leaving.... hahahahaha

That was a fowl joke so catch you later babe.

Hope things get better for you and Drew snaps out of this jelousy

thing:(

Cheers

Ken

Guest
This topic is now closed to further replies.



  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...