Jump to content
SAU Community

Recommended Posts

I have just had my car on the dyno today, and was told it was hitting a boost cut at 12psi. I thought the cut would have been higher than that. Can anybody comfirm what the boost cut is so I can investigate further if it isn't.

I ended up getting 208 rwkw at 5615rpm on 10psi with a 2 3/4 cat back exhaust, k&N panel filter and a SAFC II, so I am happy, but 12psi would make me even happier

Cheers

Glenn

Link to comment
https://www.sau.com.au/forums/topic/88600-r34-gtt-boost-cut/
Share on other sites

tats a pretty nice figure with just exhaust, filter, safc and 10 psi

satanic on this forum had 194 or something with the same mods except he had FMIC and just a catback so i guess its pretty similar

i think some ppl experience boost cut at anything above 10 with the standard ecu

i thought the safc would remove the boost cut? hmm, i guess im wrong then

Sounds like a pretty happy dyno but just the same it sounds alright to me. Knowing what I know now (as opposed to before I went too far) I would sit back and accept that as pretty good and enjoy it.

Post your dyno sheet if you like and we can comment on that.

I mean Richen the fuel, retard the timing, recover.

repeat.

I didn't want you to think I thought you were a rich retard!!!

Rich/Retard is what happens when the stock computer sees higher than expected airflow/boost etc.

Hey guys what does the standard boost gauge go up to??

does +1 mean 14 or so psi??

is it fairly accurate?

mine goes up to about 2mm from the +1?

roughly how much would it boosting do you guys reckon??

my gtt when fully boosting sometimes pops a little at around 5krpm could this be the boost cut??

i really would like to try and find out what is causing this before i go and replace coils and get safc etc??

That's not boost/fuel cut. Boost fuel/cut will make the car jerk and will throw you a bit forward if you are accelerating hard enough when it does it.

Yes 1 on the stock boost gauge is approximately 14psi.

The popping is unburnt fuel in the exhaust and nothing to worry about.

Your graph looks very similar to mine when it was tuned poorly running 13-14 psi of boost. You may want to get that checked out.

Another R34GTT tune... 208rwkw is a very good number! I presume your car is a manual? This may explain the variance of 13-14kw between yours and mine since we have pretty much the same mods.

However, if you look at the graph in my blog, you'll notice that curve does not have any 'kinks' in it... maybe if you sort that out you'll be looking at 220rwkw which should be the correct difference between auto and manual.

Hey guys what does the standard boost gauge go up to??

does +1 mean 14 or so psi??

is it fairly accurate?

mine goes up to about 2mm from the +1?

roughly how much would it boosting do you guys reckon??

my gtt when fully boosting sometimes pops a little at around 5krpm could this be the boost cut??

i really would like to try and find out what is causing this before i go and replace coils and get safc etc??

Sorry to sort of diverge from the topic but is yours a series 2 R34 because of the R34 GTT's I've seen around here (QLD), the series 2 cars seem to boost close to the +1 but the series 1s go to about the 3/4 line (the mark before) and rarely over that.

Sorry to sort of diverge from the topic but is yours a series 2 R34 because of the R34 GTT's I've seen around here (QLD), the series 2 cars seem to boost close to the +1 but the series 1s go to about the 3/4 line (the mark before) and rarely over that.

mine is a series one

with exhaust fmic airfilter.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...