Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

well , car now has new rear control arms, tie rods, hicas lock bar in , traction rods, new rear bushes, castor rods, adjustable front camber arms and new seat :P wheel alignment being done as we speak so hopefully can go get it in a few mins :D all prepped for highclere this weekend!

Spent a day with Andy.

Took Jamie for a run that night & I think its fair to say he was impressed.

Few last minute things to do and we are all set to go.

yeah, was chatting to jamie yesterday and he said how well your car went!

What's going on with my car, well it's just going onto the hoist so i can fit me new clutch,

remove the Hicas and all the line's, and fainlly fit the new front upper control arm bushes,

might even fit the ajustable rear upper arm's...

could have a bit on... :P

well , car now has new rear control arms, tie rods, hicas lock bar in , traction rods, new rear bushes, castor rods, adjustable front camber arms and new seat :P wheel alignment being done as we speak so hopefully can go get it in a few mins :) all prepped for highclere this weekend!

who did the wheel alignment? or more so who did you trust to do it lol?

Spent a day with Andy.

Took Jamie for a run that night & I think its fair to say he was impressed.

Few last minute things to do and we are all set to go.

rough figures? your not a forum warrior unless you have hektik ZOMG figures to boast about. Track times mean zilch

stock 26 on what, -5's with supporting mods with track work in mind.... thinking 18-22 psi and 340-380 RWKW's?

who did the wheel alignment? or more so who did you trust to do it lol?

this time since it was such short notice i got bridgestone select to do it, the rough alignment my mate did wasnt too far off perfect! next time might try goodyear, heard good things

GTR is currently in the garage undergoing some minor upgrades.

Turbos coming off to be replaced with a pair of new GT2860R -5's with some Tomei Expreme Dumps.

ViPec ECU is in and was running well until I decided it was time for the turbos to go.

New Castor arms up front, camber and traction arms in the rear. Camber arms for the front are currently being fabricated.

While I am doing this figured I may as well throw in a new Gates timing belt kit along with an N1 Water Pump. (Yes it does see a lot of track work so its worth the extra)

So, looking forward to the Highclere Hillclimb on Feb 13th. Should be a good shakedown for it all.

Andy wont have any problems adapting to ViPec... Did you get the plug in V66 or V88? I'd like to hear what Andy has to say about it, as I'm going to need a more comprehensive ECU when I get back.

I heard of a 33 GTR that was tuned there last week, same turbos as mine, put out 460rwkw atw on 24psi.

There is another 33 GTR getting round Hobart as well apparently that put out 440rwkw, think hat was tuned at the same place also.

Thats enough to convince me... :sick:

It's not so much the peak numbers that the cars put out, be the motors that last after he's tuned them... He tuned XRATED nearly 6 years ago now... the wot tune was spot on for racing, the stock 15yo bottom end lasted two seasons of racing before I blew it up using too much gass on a 200m skid.

460rwkw from -5's ... must be one hell of a head on it.

GL

Justin

stock 26 on what, -5's with supporting mods with track work in mind.... thinking 18-22 psi and 340-380 RWKW's?

Stock 26 with -5's, Tomei Expreme Dumps, Zorst, ViPec ECU, tuned on Premium (not Ultimate) and running a mere 17psi...

Safe, conservative and more than a handful in the wet...

Figures??? Its the times that do the talking. You can have 4 gazillion killerwasps but if you cant put them to good use then they are worthless :P

Unfortunately I blew a hose or something today at the Hillclimb and lost 90% of my killerwasps and couldn't get a run in when the hill finally dried out. Had to sit in the pits and watch while I slipped from 2nd outright all the way to 12th as everybody got good clean runs in on the drying track... :blink:

Stock 26 with -5's, Tomei Expreme Dumps, Zorst, ViPec ECU, tuned on Premium (not Ultimate) and running a mere 17psi...

Safe, conservative and more than a handful in the wet...

Figures??? Its the times that do the talking. You can have 4 gazillion killerwasps but if you cant put them to good use then they are worthless :D

Unfortunately I blew a hose or something today at the Hillclimb and lost 90% of my killerwasps and couldn't get a run in when the hill finally dried out. Had to sit in the pits and watch while I slipped from 2nd outright all the way to 12th as everybody got good clean runs in on the drying track... :)

i had such a shit day :domokun: i would of been better of running on foot for the event, bring on collinsvale i say to redeem myself lol

Figures??? Its the times that do the talking. You can have 4 gazillion killerwasps but if you cant put them to good use then they are worthless :)

Spot on. Power delivery, reliability and consistancy is they key!

The gods were unkind.

Mine blew a cooler hose off and seeing the pits were a mud bath I wasn't climbing around underneath to put it back on.

Had to watch myself drop from 2nd outright to 12th by the end of the day when the track had dried out and everybody got about 4 - 5 seconds faster. :)

Jamie took out fastest time of the day. Impressing times early on in the wet and then even more so later as the track partially dried so there were mixed conditions on the way up the hill.

Edited by SSHatch
MMMMMmmm the skyline gods were unkind.

how did Jaymie go? I think I saw his car on saturday, in the cbd which made me think he didn't attend?

jamie was up there :) he set fastest time of the day and took out the event lol.

Stock 26 with -5's, Tomei Expreme Dumps, Zorst, ViPec ECU, tuned on Premium (not Ultimate) and running a mere 17psi...

Safe, conservative and more than a handful in the wet...

Figures??? Its the times that do the talking. You can have 4 gazillion killerwasps but if you cant put them to good use then they are worthless :)

Did Andy have much to say about the ViPec? I'd be interested to know what he thought of it.

Times and mph... are the proof. I just do it for the FUN! HA hAH!

From what I can gather, Andy was his usual self and didn't really say much.

He did say that the software was pretty much just another version of the same old stuff.

He did have issues and had to use my laptop instead of his own as there is a very specific sequence that must be followed when installing everything for the first time. If its not done correctly then the wrong USB drivers are installed and the laptop wont connect to the ECU and they are very difficult to uninstall.

Jump on the ViPec website and check out the features for yourself. That and the support offered through the ViPec forums was enough to convince me to go that way.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...