Jump to content
SAU Community

Recommended Posts

I never measured it but you could use a fuse closer to the current draw of your pump. You got me interested so threw the clamp on to my car just then, 9.4A continuous didn't seem to change at all. Driving a bosch 044 intank. I dare say that a stock pump or gtr pump wouldn't use that much, throw a 15A fuse on there, the wiring will definitely handle greater than than the current required to pop a 15A fuse. Measure yours if you want, I don't have any others to compare against.

  • 2 months later...
  • 2 months later...
040 in ur 33 will b no problem

mines been in my car for 8-10 months now and never had any problems...

Yer, so will rewiring the fuel pump be necessary as it is in an r32? Will the same process be used to do so? I went out and bought all the wiring already...

  • 1 month later...

Hey guys, I did this last friday, actually in the exact same way like gumflappers' wiring diagram.

I'm currently running a stock pump, but it feels like it's running smoother through gears, turbo seems to spool a bit better... so my 'gut dyno' says it was worth effort.

But now my fuel warning light stays on all the time... haven't tried to reset the ECU, but I don't think that'll solve the problem.

Anyone who has come across this problem?

Taking the bulb out is no solution haha :P

If somebody could help me out on this one, please do :)

I opened up the fuel pump wiring assembly or whatever you'd like to call it, looked at the pins, but it looks fine, and should make contact (just like it did before I started out modding it)... the pins are locked firmly in the plug, as they were before I even touched them.

This is how I did the wiring;

12v%20wiring%20pump.jpg

(I took the relay from the diagram by 'gumflapper').

I first depinned both ground and '12v' feed wire from the plug, then cut off the stock wires from the pins, and soldered the new thicker wire to the pins... the two pins fit well inside the plug and are not loose or something like that.

To get rid of the fuel-light coming on in my gauge cluster, I also tried to get the ground for the pump from the original loom, so the diagram looks a bit like this;

12v%20wiring%20pump%20stock%20ground.jpg

It still had that friggin' light in the gauge cluster :/

I then put it back to the first situation, and took the ground wire from the battery of for about 10-15 minutes, pushed the brake pedal a couple of times, doors open with dome light 'on', etc.

Still has the light coming on :)

What seems weird to me, is that when I meassured the voltage at the three-pin plug, I read a higher voltage when using the ground from the stock pump loom, than when I used a ground from a bolt in the chassis.

What am I doing wrong in all this?

Also, anybody who knows what the two-pin plug is for?

I don't read any voltage from both, with ignition switched on and off, and using the chassis as well as the stock loom for ground.

There's nothing about this in the service manual (that, or I just didn't find it).

Edited by stefan-w

hey

your much better off grounding the pump either to the battery directly or close to it. gounding it thru the wiring lume will reduce the voltage that the pump recieves therefore defeating the purpose of this mod.

post-44390-1254914219_thumb.jpg

in the photo above, you can see the 6mm brown and blue wires that feed the fuel pump. i would be checking the other smaller wires in the tank. i assume (never checked them myself) that they are from the low-level sensor. make sure all of ur wiring is correct and secured/soldered properly and check that all the plugs/sockets are locked together firmly.

however upon looking at that image there seems to be a few more wires in the tank (bottom rhc)... any ideas on what they could be?

I've got ground directly from the battery, just like the 12v feed... it's exactly as in the diagram you made :banana:

Only I used black and red wiring haha, the loom only powers the relay.

That second diagram I've posted was a try, to see if that would solve the problem (wich it didn't, so I went back to your wiring diagram).

Only now do I see you've pulled but wires to the pump, not just to the plug on top of the tank (wich I did)... this shouldn't make a difference I hope?

I'll do so when upgrading the pump, but not on the stock one.

Is that unprotected wiring and an open plug floating around in your fuel tank? :dry:

Are you sure that's entirely save?

i thought the same thing when i took out the stock pump (WTF r all those wires floating around in my fuel? :S) i decided not 2 fix what didnt seem broken... lol

"Only now do I see you've pulled but wires to the pump" i dont understand :S

Crap... 'typo', and I should have written it a bit more clear :rant:

What I meant; I only replaced the wiring up to the female connector (wich goes on top of the fuel tank).

I noticed just then that you have also replaced the thin stock wiring from the male connector to the pump itself, inside the fuel tank... obviously, I did not.

I don't think that'll cause my light to come on though, but I'm no expert.

replacing the wiring to the fuel pump inside of the tank itself will have nothing to do with the low-level sensor... 2 b honest i could not tell you what the sensor even looks like as ive never pulled it out. i had enuf trouble getting the fuel pump in and out let alone the low-level sensor.

  • 3 months later...
pidibump!!

I read the whole 12 page thread. Most people talk about r33 or 32 gts or 32 with Aftermarket pump.

What about Stock fuel pump on a GTR 32 with something like 350whp.

Any benefit?

Maybe, that this help you out:

http://www.stealth316.com/2-fuelpumpguide.htm

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Please use a modern ECU. PowerFC with the Nintendo Gameboy controller is horrible. It's not 2005 anymore.
    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
×
×
  • Create New...