Jump to content
SAU Community

Recommended Posts

wrong part of the forum dude.... it clearly states "For Sale (Private Car Parts and Accessories)" which u had to click b4 u posted...u might want 2 try and post in the "Forced Induction Performance" under " Modifications & Maintenance " towards the top of the forum page.

... 4 got 2 add.. "nice car!!"

Edited by Player_Hater

you need to specify some more specs.

Is it stock motor with all the show attachments?

Is it a built motor?

How much power does it make, what is the response like?

One pic has a Trust turbo, the other has a HKS turbo... which one are you using?

IF you want answers your going to have to provide a LOT more information... attaching loads of pics really doesnt help anyone.

THE TRUST TURBO IS COMMING OFF AND THE HKS IS GOING ON ...THE ENGINE HAS HAD SOME WORK DONE TO IT ALSO.

THE HEAD HAS 2MM OVERSIZE FERRERA VALVES ,TOMMIE 270 DEG CAMS CUSTOM LIFTERS ,PORTED OUT ,FERRERA DOUBLE VALVE SPRINGS,BOTTOM END HAS CP PISTONS, JE OVERSIZE RINGS ,BORED OUT , HEAT TREATED CRANK SHAFT, RACE BEARINGS , THEIR HAS BEEN A HEAP OF OTHER STUFF DONE BUT I GOT 490 RWHP ON 1 BAR BOOST WE HAVENT TUNED IT PROPERLY YET WAITING FOR THE NEW TURBO TO GO ON AND I AM GETTING A BIGGER INTERCOOLER...

I WANT TO TRY AND GET 700 RWHP...AND A 10 SEC PASS..

i run a digital ignition msd with 6 v8 supa coil packs its putting out 400 volts not nice if you get a zap... motec m8 pro runs the car has about 8 thousand worth of upgrades i got it out of a v8 super car last yea just after they had to change their computers to m800.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...