Jump to content
SAU Community

Recommended Posts

Post up anything that u can know is a substitute / compatible with other models for either stock or upgrade parts. Including part numbers could also be helpful...

*LIST UPDATED 29/11/06*

IF ANYTHING SEEMS INCORRECT OR YOU HAVE SOMETHING TO ADD, POST IT UP!!!

- Aircon dryer condenser (i think thats wat it is) = maxima a32 (Resin)

- Alternator = R31 and VL Como, More info Click Here

- AFM upgrade = Z32 which is a direct fit, plus pinouts are the same (Huddy)

- Boss kit for 89 A31 Hicas model = s13 non hicas boss kit (skypy12)

- Brake Pads = Bendix Pads Code DB1485 from a j31 maxima 2003 model onward are the exact same pad as the rb20det cefiro (Resin)

- Brake Rotors 2 Pod Rear upgrade = 350z, discs need redrilling to a 4 stud (adrnln)

- Clutch Master Cylinder = R32

- Clutch pedal box = R32 Gtst works, however S13 is too short (QUIKBLADE)

- Coilovers = S13 although stiffer spring rate recommended due to heaver motor

- Coilpacks (cefiro rb20) = CA18/RB20-Redtop

- Cross Member Front = R32

- Dash upgrade/change = Laurel

- Diff = S13/R32 - either R180 & R200

- Door Hinges = R32

- Drift Handbrake Button = R32

- Drive Shafts = S13 / R32

- Front Seats upgrade/change = R32 /R33

- Front Spoiler Lip = S13 lip turned upside down, More info Click Here

- Front strut brace = A31 preferably, or 13 depending on clearance height

- Fuel lid spring = u12 pintara Nissan

- Gearbox / handbrake boots = r32gtst boots from jaycar with some possible modding. (someonestolecc)

- Gearbox = rb20gearbox / rb25gearbox(few other changes needed) More info Click Here

- Gearbox Crossmember = A31 Manual Gearbox cross member is the same as CA/SR Manual item.

A31 Auto Gearbox cross member is the same as R32 Manual item. (C_DawG) Disscusion Click Here

- Half Shafts = S13 / R32

- Handbrake Cable, Not footbrake - pretty sure you CANT use 32 gtst / 4 door? most nissan ones should fit theoretically - but in cefiro usually come up a little short (Huddy)

- Handbrake Shoes = R32 and possibly R33 and S14, Read more Click Here

- Intercooler = Any FMIC cooler will fit with enough cutting and shutting of the front bar... if talking about piping, the R32 piping needs to be cut slightly. EG: Pipe which goes across the front of the engine and then joined with a silicon pipe for example. R34 gtt stock sidemount intercooler is pretty much a straight swap into a ceffy. You use the ceffy bracket and cut of the piece for the snorkel off with a hacksaw. You also need to cut a section of of the splash guard cause it sits lower than the stock one.

The ceffy sidemount set up is very similar to the r33 and r34 not r32 (Resin)

Stock Front Bar pics with FMIC install - Click Here

- LSD Diff = S13 / R32 = R200, or if you got a single spinner, the R180 from both the non turbo s13 and r32 would also fit.

- Oil Filter - Click Here

- Power window mechanisms = R32 4 door (although been suggested that doesn't work for the rear, Reference ) however power window amplifier for the rear windows that does work is

nissan part number # 25424-71L00 (drivers side)

- Power Window Relay = bluebird ones fit straight up (not sure what year model... its the one with the SSS variant) (insanity)

- R33gtst gearbox upgrade speedo adapter = R33gtst item ~ $50 second hand or Nissan Nivara speedo drive, for ~$22 brand new from nissan. And the red speedo gear that comes off the R33 speedo drive. Put them together walla, working speedo. (dangerous_daveo) Click Here for details on RB25 Gearbox upgrade to Ceffy

- Radiator = R32 gtst and gtr, The radiator for the A31 20DET isn't same as R32 20DET, though they are direct swap (Something like A31 uses single core and R32 is twin core??). CA S13 also fits, but that would be a downgrade, might get you out of a tight spot if you are stuck on the side of the highway or something?

R33 GTST rad+shroud (bigger than R32) fits into A31 but will not fit into S13 (fouls on bonnet). Have to make new top brackets for R33 rad. (daisu)

- RB25DET Engine Upgrade - Click Here

- Radius rods, lower arms = S13

- Rear Cradle = R32

- Rear strut brace = r32 / s13

- Seat Belts = R32, and Pre 1997 A32 maxima (after that they came with pretensioners).

- Seats = R32 and R33 do fit however for S13 seats, modifications are needed.

- Speedo cable = R32 / VL commodore

- Sunroof -> S13 sunroof = NO... not 100% sure but from what i've seen they have different mounting points etc and possibly different size...(Huddy)

- Swaybar, bracket, bushes, bolts, links = S13, R32 GTR swaybars also fit. (ls1ben)

- Stereo Wiring - for diagram Click Here for PDF file

- Tie rod ends= s13, r32, r33, A32 maxima (More info Click Here )

- Upgrade 4 pot brakes with 4 stud = R32 gtst calipers with R33 non turbo disks and R32 master cylinder , just need to get appropriate brake lines and cut the disc shroud a little and you have budget big front brakes (Huddy)

- Upgrate 5 stud = R32/300zx/S14 hubs

- Water Pump = Rb30/VL Commodore

- Wheels / Offsets - Click Here or Here Also

- Steering box = 180sx

- Rack and pinion = 180sx

Please note if you can't find something in this list it may be found over at D1NZ which also has alot of A31 info.

Edited by skypy12
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/93523-a31-cefiro-parts-list/
Share on other sites

Tie rods ends are the same as a A32 maxima.

Seat belts are the same as R32, and Pre 1997 A32 maxima (after that they came with pretensioners).

Power window mechanisms are the same as R32 4 door.

Does anyone know what rear discs can be used on an A31? As the skylines have drum/disc combination brakes, which I don't think the ceffy's got.

also... if doing a 33gtst gearbox conversion Kansai automotive have the adapters so that you can get the speedo working... (32 cable and 33 not cable or something)

:D

Thats easy, Nissan Nivara speedo drive, for $22 brand new from nissan. And the red speedo gear that comes off the R33 speedo drive. Put them together walla, working speedo.

Does anyone know what rear discs can be used on an A31? As the skylines have drum/disc combination brakes, which I don't think the ceffy's got.

Sorry don't know the discs, i upgraded all mine to r32 stuff.

mine cefiro had drum/disc combination for the rears when i got it. though i have spoken to another guy and he had a different setup on his. Mine originally came from factory as a rb20de, so maybe the rb20det versions had a different setup.

- Front Seats upgrade/change = R32 /R33

- Upgrate 5 stud = R32/300zx/S14 hubs

Does this mean GTR or GTS-T seats? Or both? So they are straight fit to existing rails??

Also, R32 Brembos as found on V-Spec or GTS-T once again?? And does this mean both front and rear calipers and rotors can be changed with the 5 stud hub?

Edited by QUIKBLADE

when i bought my car it didnt have a spring in the fuel lid so when u pulled the lever the door wouldnt open. Well i tested the spring out of my old car (u12 pintara nissan) and its fits exactly dunno whether its the same for all nissans but yea if ur spinng in ur fuel lid ever brakes or u loose it u know where to get one from

Edited by Resin
Does this mean GTR or GTS-T seats? Or both? So they are straight fit to existing rails??

Also, R32 Brembos as found on V-Spec or GTS-T once again?? And does this mean both front and rear calipers and rotors can be changed with the 5 stud hub?

sorry i don't personally know with the seats. But i know the standard r32 gtst front and rear calipers and rotors bold and line straight up on the cefiro with the 5 stud hub. Only issue from memory was either the front or the rear had to have one of the brake line ends modified. If the bembos generally bolt up on a r32 which normally has standard brakes then i'm sure the vpec ones would too on the cefiro.

Edited by skypy12
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...