Jump to content
SAU Community

Gb: R33 Gts-t And Gtr And R34 Gtt Radiator Guides


Recommended Posts

Hey ppls.

I'm extremly sorry about delay with group buy.

I've had a lot of life changes in the mean time but I digress.

The R33 Series I, Stag Series I, R34 GTT (all) guides are all being cut at the moment.

I have the cardboard boxes for freight in the factory and I will begin making them up shortly.

The R33 Series II guides are STILL not finalised but I'm doing some grinding on it today and I need somebody who can come ot Dandenong to trial fit it. I'd come to you, but I need to use a grinder to make any mods and the factory here has all that stuff.

The Stag Series II guide sample will be send out to two guys in Canberra to fit to their car and try it out. I think it should be pretty good, but it may need some slight re-modelling.

Again, I'm super sorry about the delay, but understand that I will supply each and every one of the guides as soon as I can.

I thought I'd be able to finish them a lot faster than I have. I've had a lot of stuff go on in the last few months. It's been crazy.

Yours in total apology

BASS

  • Replies 520
  • Created
  • Last Reply

Top Posters In This Topic

Hey,

I'll DEFINATELY take one for an R34 GTT with a Nismo front bar!

Let me know as soon as you need money for it + freight and ill transfer!!!

PM / Email / Phone me if you need to!

Thanks.

Hey ppls,

Just got the phone call and went and picked up the blanks.

So, I have all the Series II Stags, the Series I R33, all the R34 guides in the back of my car.

I'll be testing a revised R33 Series II guide on a car on the weekend and a Series II Stag also.

The end of this group buy is nigh. Finally. :S

Cheers

BASS OUT

post-6399-1158282467.jpg

R33 Series II guide modified.

It's been ground and the bend changed and will be trial fitted again to Dezz's car on the weekend.

Hopefully she'll be all good this time.

Cross your fingers.

These are still available Bass? I'd like one for my R34 GTT... think it's a standard nismo front bar. Could you pm me the details? Cheers.

  • 2 weeks later...

Bass Junky or Dezz, any updates on how the fitment went?

I know there have been problems but one more month and this has been going on for a year, and payment was in Feb! That was 8 months ago! It's getting ridiculous.

Hi Guys.

Again, I sorry about the delay. I have not stopped on this bloody project.

I took the guides to a plave near here last week and went back a few days later and they then told me they couldn't do it because they are too busy and blah blah blah.

So shortly I'm going out to find antother person.

I'm also playing with Dezz's car tomorrow.

Stay tuned.

TOP NEWS PEOPLES

I have finally trail fitted the R33 GTS-T Series II guide to Dezz's car and lo and behold, it's spot on!

A very minor adjustment to an angle and she's apples!

I'll be sorting out hte order to the laser cutters on the next day or two and then away we go.

THANK YOU EVER SOO MUCH FOR YOUR PATIENCE.

Bass Out

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...