Jump to content
SAU Community

Recommended Posts

Sick of my clunking 2 way as its a mainly street driven car....

3 options :

1) S15 centre - whats the go with installing this into my r32? What do i do about the half shaft bolt pattern, as i understand u need to use the s15 half shafts. Are the s15 and r32 halfshafts interchangeable?

2)Quaife (torsen) centre - very expensive, but it is a straight drop in i believe?

3)R34 GTR V-spec - i think i read somewhere that they came out with a helical centre....but whats the chance of picking one these up... :)

This link gives info on how they work, and how the more popular clutch centre works, as well as the pros and cons of each. - http://www.houseofthud.com/differentials.htm

Im just after a centre that doesnt clunck at low speeds, as well as the performance of a locking diff....

So - Looking at the above options 1) seems the cheapest. What is required for the s15 centre to go into my car?

Any other opinions or options are welcome :)

edit/ as a side note, im also lowering the ratio from 4.3 to 3.9 :)

Edited by Bl4cK32
Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/
Share on other sites

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Nismo GT-Pro 2 way with adjustable pre load.

I would sell it if the price was right. Remember this is the GT-pro though, cos the regular one which isnt adjustable goes for like 1k

Its done less than 10,000. Previous owner ran it in, then ive used it for less than 5,000kms...had 2 or 3 oil changes since new too...came with new everything-sideshaft bearings etc....

attached pic shows what i mean...mines set to soft atm.

On topic - Anyone can help me?

post-3692-1132465566.jpg

Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/#findComment-1730023
Share on other sites

well if I was looking for a diff I would offer to take it off your hands for free :)

All you need to do is adjust the preload, that is the only thing that makes it so tight the wheels skip. If they still skip at minimum load you need to get the centre out and remove a shim or two from each side, its that easy.

There is nothing about a mechanical diff that makes it tight except the shims :D

On the other hand, once you are happy with how tight it is, they are unbeatable for driving performance.

Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/#findComment-1730061
Share on other sites

yeah, i've heard nismo gt-pro's are quite tight.

eventually the shims will wear out a bit and it'll loosen up, man i would kill for a nice tight 2-way like that( toite like a tiger...). but i'm too poor

/pulls out the mig welder

Edited by MerlinTheHapyPig
Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/#findComment-1730080
Share on other sites

All you need to do is adjust the preload, that is the only thing that makes it so tight the wheels skip.  If they still skip at minimum load you need to get the centre out and remove a shim or two from each side, its that easy.

There is nothing about a mechanical diff that makes it tight except the shims :)

Define what you mean by skip please Duncan?

I think i know what your geting at. I'll adjust up the setting and see how it goes and report back :D

Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/#findComment-1730157
Share on other sites

sorry, i assumed the thing that was pissing you off about it is that when you do tight turns at slow speeds the inside wheel skips making a nasty clunking / shuddering?

I can't think of any other problem you would notice with a tight diff?

Just loosen it off enough so it doesn't annoy you :mellow:

Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/#findComment-1730446
Share on other sites

Trying to get my head around it still sorry Duncan :P

By loosening it off do you mean tightening or softening the pre-load? Its set to the softest (low) setting atm.

Does that mean the only option is to remove a shim or two?

And by doing this, it will effectivly stop the clunking / shuddering etc at slow speeds?

Sorry for the Q's :) One last one though - I still like the idea of the helical diff because of the non service aspect (clutches to wear out). Which one would you put in a street car, and why?

Edited by Bl4cK32
Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/#findComment-1731092
Share on other sites

I sent an email to Quaife and and still waiting to hear back.

OR - i need to find out how to fit a s15 helical centre to my car, as the half shafts (going from viscous to helical) are different (length and bolt pattern)

im not after a shimmed std diff :( I want to go helical as there is no maintenance. Shimmed std. will last sfa. I need a replacement helical, or i keep the one i got :D

Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/#findComment-1732694
Share on other sites

sounds expensive though. let me know what they say.

But, for the $2k+ this thing may cost you. Is it worth it? your nismo gt will last ages if it's only done 5000kms and is still nice and tight

so, expect to get $1k for your old diff, $1k difference will pay for at least one diff recondition down the track.

If you don't drift, it should last 1-2 years easily i reckon, I know people who have had 2-ways last them longer than 1 year with regular drift without reshim (diff in question is still working great)...

no maintenence? any lsd will require regular oil replacement etc.

Edited by MerlinTheHapyPig
Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/#findComment-1732750
Share on other sites

Im really after info on how to do the s15 swap. This is my first choice, beacause as you say the Quaife is an expensive option. S15 centres are helical, and they drop in, its just the damn half shafts...

I know the oil changes count as maintenance, i was referring to pulling the whole diff out for new clutch plates etc...:)

Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/#findComment-1732830
Share on other sites

factory helical difs are fantastic with standard power.

put some torque through them and bang.

the lsd efct is done through the gears trying to push themselvs apart in the centre against the centret casing(in short).

the gears simply arnt strong enough for the extra power.

if they open wheel(which they do)it doent take long for them to break

a good mechanical clutch pack lsd is the go.

ps the halfshafts are all diferant on the inside of the diff.

also r34gtt manuel cars come with a helical centre. gtr does not.

cheerrs.

Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/#findComment-1733179
Share on other sites

They must be strong or Quaife wouldnt offer a lifetime warranty with them. This warranty applies even when raced - no one else does this. Quote "proven in everything from SCCA Rally to Formula 1"

Nissan must have thought they were better as they swapped using the vlsd for the hlsd from the s15, and the r34's...

I agree with what most of you guys have said about clutch pack lsd's. Im just getting sick of the shudder. My car isnt too bad with the wheel chirping. I can live with chirps, but shudder is annoying when cops look at you already...

If it comes down to it, i'll live with the 2 way, but if i can find a simple fix (s15, or r34 centre into my housing) for cheap, then i'll go with that :)

Edited by Bl4cK32
Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/#findComment-1733229
Share on other sites

Nissan must have thought they were better as they swapped using the vlsd for the hlsd from the s15, and the r34's...

S15 centre is a Torsen, not a Quaife. It's actually what is known as a Torsen Type 2, which is not particularly strong due to the long, spindly nature of some of the internal connecting gears. The Torsen Type 1 is a much better design and used in some Toyota's, I believe. Don't know about R34's - I've only seen pictures - but the centre looks very similar to the S15 type.

Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/#findComment-1733290
Share on other sites

Darren...

how could you want to sell the Nismo GT Pro? :P

Especially since you bought it from me freshly run in! haha.. It's such an awesome diff, you'll miss it when it's gone......

One my GT Pro in my S15, I found that setting the initial torque to medium made it nicer to drive. Sure it still clunks, but with regular oil changes (castrol diff oil, 75w140 i think) and the medium setting, it's a lot more tolerable. At lower speeds, just need to either work the clutch, or slide the tyres around :P

take care!

KJ

Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/#findComment-1733455
Share on other sites

The S15 runs the eact same diff center as the R34 GTR.

S15 diff being weak; what power level with what tyres are we looking at SteveL?

It's actually torque that kills these - the achilles heal of the Quaife/Torsen centres is pretty much the same: sudden application of load to one wheel causes overload of the internal gears dues to the nature of the way they work. For example, lifting one wheel through a corner and then having the same wheel suddenly take up load again.

Link to comment
https://www.sau.com.au/forums/topic/95568-helical-diff/#findComment-1733491
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...