Jump to content
SAU Community

Recommended Posts

guys what is the main diff between the 2 turbos below:

HKS - GT Sports Turbine Kit - 2835

HKS - Turbo Kit - GT-RS -

now why i ask is apprantly there both rated at 400ps.

so yeah me confused.

anyhelp would be good ;)

thanks in advance

Actually both use the Garrett 71mm GT35 BCI 18 series compressors in 52 trim though optional on 2835's 48 and 56 trims .

Main difference is the turbine , GT-RS is the fancy name for a Garrett GT2871R with the middle or 52 trim compressor . All 3 2871 cartridges use the 53.8mm GT28 turbine in 76 trim (NS111 type) . Also avail in 48 and 56 trims .

HKS GT2835 and some Garrett GT3071R's (WG type) same cartridges use a 56.6mm cropped GT30 UHP turbine .

The theory is larger turbine makes for better "balance" of compressor to turbine size ratio .

Make careful note that HKS generally stick to smaller trim compressors than Garrett do - the result is better response or lower boost threshold if you like .

As for the 400PS , the GT-RS would be on its knees from a turbine inlet (back) pressure point of view .

PM me if you want all the numbers n bits n pieces .

Cheers A .

GTRS's on gtr's are capable of much more than 300awkw. how ever were talking about just a single turbo kit.. the disco potato is a GT28rs rated between 320 and 350 from memory and they are a excellant turbo for a sr20 for response

from memory there was someone of the forum makeing 270rwkw in a 33 gtst with a hks gtrs and suitable mods to go with it

Wazz

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...