Jump to content
SAU Community

Recommended Posts

Mate that was some awesome burnout, was starting to get really jack of the sh!t performances out there, then you took it up a notch. :)

I *MIGHT* have some on my camera but i can't remember I'll check it out tonight.

Edited by Oosh

that pad is f*kn shithouse. buy the 3rd round i was hitting the pot holes and it was f*kn up my spin. theres no room to swing a cat and they told me if i stand still again i'll get disqualiphyed.

speedway city ownes collinsgrove.

but i hear there are new pads coming up all over the place..

Talemn Bend anyone.

Yes, we decided that the burnout pad really needed to be about 1/3 longer in each direction to swing cars around without fear.

Happy Birthday to my wife as well, who let me go instead of shopping with her and her family on her birthday!!!

mmm so chunky you can carrve it..

close. its the quad cam VG same at the z32's but only single ball bearing turbo. forgies and shot peened rods, stock.

running 10 w/o cooler. coolers coming from japland atm.

Head up to Blackwood Auto and Dyno.

$35 for a power run. :(

My Rb30DET running the stock rb20det turbo where it made 176rwkw at 9psi, which is most definitely slower than how it feels now without a tune running the vg30det turbo.

Mine will spool up to 13psi by 2100rpm (appears to surge or some thing under that) general driving say rolling out of a corner at low rpm and booting it will see 13psi or so at 2500rpm. It appears to pull hard until 5800rpm, all though it does go a lean after 5500rpm. Needs to be tuned.

Edited by Cubes

that van allways puts on a good show.

but after all that i got second in the 6cyl class, beaten by the UC torry cause 3rd round f**ked up.

there were potholes in the pad by the 3rd round. it was a joke. i didn't know what was stopping my spin till after. i thought it was the rear bags were failing but i was hitting the potholes stopping my slide so i was getting stuck up against the armco. and pissed off so stuffed the rest up.

bloody good day thoe. some very quick cars and some... well...

i heard from an offical that the kingswood rocked up with a generator belted up in the passenger seat with an extention cord running to a leafblower set up as a s/c..... :lol:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was just driving into work and while on my drive, I went to accelerate and noticed the car would sputter/hesitate and I’d hear a few pops from the exhaust before it started going faster. Then I also noticed that when I push my clutch in, the car would die. This all started happening today. Any ideas?
    • That is a lovely Volvo, just saying. Yes I should have got an 260RS when they were cheap. I do regret now.
    • ^ lots of good points made above. The thing is, "aggressive" or "flush" fitment is relative depending on how much you have been influenced by social media. My starting point is always "look at the Nismo RWD specs". That is where you should start, then start measuring as GTSBoy as sort of mentioned, because every car will be slightly different. My 8.5"+35/9.5+38 will not be "flush" enough for you because you want more "pumped" look, which is why you measure. Tyre sizes and brand/models also make a difference. Some tyres are more chunky/square, some are more rounded. That means you could get away with more aggressive offsets without rubbing. But then it also depends on your ride height. Also depends on how much your car copped damage before being shipped from Japan. So it goes back to measuring your car yourself and determining what can work. Those Nismo specs are used bacause it's a safe spec for standard car (suspension. body) with chunky tyres. But then I put 265/35 wide tyres on R34 GT-R wheels, and currently run 285/30 tyres on 18x10 wheels.
    • Sounds pretty awesome. I recommend creating a new build thread and posting all your goodness in there.
×
×
  • Create New...