Jump to content
SAU Community

Collingrove Hill-climb

Sambo33

By Sambo33,
in South Australia

 Share

Recommended Posts

Oosh Veteran

Oosh

Posted
Posted (edited)

Mate that was some awesome burnout, was starting to get really jack of the sh!t performances out there, then you took it up a notch. :)

I *MIGHT* have some on my camera but i can't remember I'll check it out tonight.

Edited by Oosh
Naife Enthusiast

Naife

Posted
Posted

that pad is f*kn shithouse. buy the 3rd round i was hitting the pot holes and it was f*kn up my spin. theres no room to swing a cat and they told me if i stand still again i'll get disqualiphyed.

speedway city ownes collinsgrove.

but i hear there are new pads coming up all over the place..

Talemn Bend anyone.

chops Experienced

chops

Posted
Posted

Yes, we decided that the burnout pad really needed to be about 1/3 longer in each direction to swing cars around without fear.

Happy Birthday to my wife as well, who let me go instead of shopping with her and her family on her birthday!!!

Naife Enthusiast

Naife

Posted
Posted

mmm so chunky you can carrve it..

close. its the quad cam VG same at the z32's but only single ball bearing turbo. forgies and shot peened rods, stock.

running 10 w/o cooler. coolers coming from japland atm.

Cubes Grand Master

Cubes

Posted
Posted (edited)

Head up to Blackwood Auto and Dyno.

$35 for a power run. :(

My Rb30DET running the stock rb20det turbo where it made 176rwkw at 9psi, which is most definitely slower than how it feels now without a tune running the vg30det turbo.

Mine will spool up to 13psi by 2100rpm (appears to surge or some thing under that) general driving say rolling out of a corner at low rpm and booting it will see 13psi or so at 2500rpm. It appears to pull hard until 5800rpm, all though it does go a lean after 5500rpm. Needs to be tuned.

Edited by Cubes
Naife Enthusiast

Naife

Posted
Posted

that van allways puts on a good show.

but after all that i got second in the 6cyl class, beaten by the UC torry cause 3rd round f**ked up.

there were potholes in the pad by the 3rd round. it was a joke. i didn't know what was stopping my spin till after. i thought it was the rear bags were failing but i was hitting the potholes stopping my slide so i was getting stuck up against the armco. and pissed off so stuffed the rest up.

bloody good day thoe. some very quick cars and some... well...

i heard from an offical that the kingswood rocked up with a generator belted up in the passenger seat with an extention cord running to a leafblower set up as a s/c..... :lol:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...