Jump to content
SAU Community

Recommended Posts

  • Replies 100
  • Created
  • Last Reply

Top Posters In This Topic

R31...

They are better sorted from factory.

Lower diff ratio that accelerates the car quicker.

Better cooling system setup.

Nicer stiffer chassis.

My sister recentlyish bought a NA VL that had done a genuine 137,000km's. It was spotless.

First thing we did was throw a bran spankin new radiator in it, new genuine nissan thermostat, new clutch fan and gave the whole system a power flush.

~9months later without a warning it started to run on 4cyl's.

No overheating nothing, it sat solid on the 2nd notch. 1 nasty arsed cracked head. The cooling system was perfect, there was ZERO reason for the crack.

Now its sitting in the old mans shed next to her previous VL that also has a cracked head. :S

I prefer the exterior look of the VL, especially a nice dark coloured VL Calais.

Edited by Cubes
Link to comment
https://www.sau.com.au/forums/topic/98189-r31-or-vl/page/2/#findComment-1785469
Share on other sites

When you swaped the radiator/cooling set up

did you blead air out of the system?

There is one little bolt that you losen to let air out after you have added the fluid. oppsite side of the engine to the alternator should be a little yellow sticker

How did you pick the cracked head:

Oil in cooling fluid?

Big mofo visable crack?

Running on only 4 cyclnders i.e. missing when ideling?

Compression test?

Sounds like a good time to swap heads or even engines!

Edited by NAman
Link to comment
https://www.sau.com.au/forums/topic/98189-r31-or-vl/page/2/#findComment-1785717
Share on other sites

Yes Cooling system was bled.

Running on 4cyl's is zero compression in cyls 5 & 6.

There was no oil in the coolant or vice versa.

The head simply cracked, lost compression in cyls 5 & 6 and 100psi in cyl 4, it ran like a pig, sis drove for 10km's to home.

VL's can sometimes run for months with cracked heads and no tell tale signs, depending how bad its cracked.

The water in the oil usually shows up in the PVC valve before anything else all though there was none in there.

I was hoping a headgasket as it went so suddenly, no tell tale signs like usual. It simply cracked and cracked bad.

It wasn't using any water, it was running perfect and not thrashed prior to the head crack.

Ripped the head off.. she's cracked. :P

Its simply holdens lack of R&D in fitting the rb30 in to the VL + the fact the rb30 head does have a weakness. R31's crack heads too... just not if the cooling system is good unlike the VL's.

A mate of mine had the same thing happen to his VL. Perfect working order then crack.

The VL I bought when I was 18 never cracked but I did sell it within 9months to upgrade from that yucky interior.

My RB20DET was cooking and I didn't realise due to just purchasing the car, just smelt hot and spewing out coolant. It ran like that for a complete summer, replaced the temp sender realised it had been driving around on the H!!! That still ran fine for many years after and a solid 100,000km's. :D

Edited by Cubes
Link to comment
https://www.sau.com.au/forums/topic/98189-r31-or-vl/page/2/#findComment-1785743
Share on other sites

If you wanted un un-biased opinion, this isn't really the place to ask.

Wow, what a surprise, everyone says "go for the Skyline"

Now go and start a duplicate of exactly the same thread on http://www.calaisturbo.com.au and see what sort of response you get.

:P

I vote you got for the VL.

Link to comment
https://www.sau.com.au/forums/topic/98189-r31-or-vl/page/2/#findComment-1785862
Share on other sites

My only worry is that he will just assume we are all biased because this is a Skyline forum. Its not all bias, the reality is that the Skyline is the better car. I'd be interested to hear what points someone could put forth to say the vl is better, other than they like the look of them better.

Link to comment
https://www.sau.com.au/forums/topic/98189-r31-or-vl/page/2/#findComment-1785977
Share on other sites

I can't say I'm a fan of the R31 looks (apart from the coupes).

None the less here's my argument against the VL.

OMG... WHAT CHASSIS RAILS!!! No wonder they have been known to pop windscreens and flex like buggery.

Which would help explain why they weigh damn close to the weight of an R32 that is a smaller car.

Edited by Cubes
Link to comment
https://www.sau.com.au/forums/topic/98189-r31-or-vl/page/2/#findComment-1786020
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
×
×
  • Create New...