Jump to content
SAU Community

Recommended Posts

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

You bitches all copied me :P

well I was officially the first skyline to get the white ones at least.....tempe JUST got them in stock the day I went.

but meh...now more than ever I wanna get a set of Rays....

stan you should have went the 19s.....they have a better and wider dish. The dish is rounded and not edged.

I didnt want 19s on it again so I went for the 18s.

Edited by shonen
  • 3 weeks later...

OMG WHAT HAVE I DONE :( Definitely got to make a note of this "grand" achievement somewhere :rofl::)

Beer Baron: How farkin' slow was that cabby going eh? I ended up getting the shits as you may have seen :(

Flip: The front lip was from CarMate... $280 me thinks, not including spraying and fitting/modifying to fit :)

Beer Baron:  How farkin' slow was that cabby going eh?  I ended up getting the shits as you may have seen :(

haha, yeah you needed to pull the little manouver that i did a few metres ealier, then you could have been clear of me and the taxi in one hit. i was just cruising along. :rofl: taxi was good for a laugh, as soon as i get along side he suddenly had an urge to go 10-15kms faster than he was before... nice one.

do you guys think the impul copy's wil fit on a r33 with the 9.5 rears in 19"?...as my car sits pretty low with the cusco suspension (guards have been lipped)

as all the ones i see with the 18" 9.5's, the tyres get pretty close to the guard and look like they will touch if they sat lower.

Cheers ...Jim

yeah Vork racing Ravs engineering rims are just as cool as the impuls. if not cooler. If i get a set of TE37s i should get some of the ravs engineering stickers to put on so no-one tries to steal them.

Jim it's hard to say because

A) We don't know how much your guards have been lipped.

B) We don't know how the aftermarket suspension has affected clearance.

Best bet is to go there and try em out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...