Jump to content
SAU Community

Recommended Posts

R33 seats have two bolts on the sidewall of the footwell. 12 or 14mm bolts. Then you should be able to slip them out a bit, and you'll see two more bolts for the rear part of the seat, same sort of sizes. (located between the bottom seat and back-rest of the seat, behind where the seatbelts run across)

The rear part of the seat should then lift upwards to get it of the hangars, and there is one hangar that holds onto the bottom part.

If 32's are anything like that, go for it.

My 32 seats were a bitch to get off and put back in. You have to pull the bottom part off first, there should be 2 clips that will just come out with some force. Then there should be 2 bolts holding the lower part of the back part on. Undo them and then just lift the back part up.

Sounds easy but for some reason my clips and other parts didnt line up exactly, really annoying.

  • 3 weeks later...

ove had my 32 for 5 years never been able to get the bottom of the rear seat out but never realy tried that hard just worked around it as far as teh back piece goes just two bolts under the sides of the bottom part of seat these can be quite interesting to get back in tho good luck

That bent from an accident comment is plain stupid. lol, if that were the case the thing would be driving down the road with the rear wheel on one white line while the opposite diagional wheel on the other. lol. :D

I've tried and failed.. All though I could have given it a bit more of a heavy hand.

After putting a stereo in and out of my car 3 time (I did it for the previous over before i owned it) I have had to remove the back seat a few times.

The two clips at the front of the rear seat should need a bit of force, but nothing sensational. Although I did smack my head on the roof when I did it the first time... When putting them back in, because you slip the back of the bottom section under the backrest, the seat comes down on an angle, meaning you have to push the seat down and backwards to get them back in.

More annoying things tho... There is a hole in the floor unto the seat for the seat to clip into, which has a plastic... thing in it. My plastic bit was bent which made it even hard to get back in sometimes... Nothing that 10 minutes of frustration can't fix.

- Crimpage.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to Skyline ownership. Yes, it is entirely possible parts websites get things wrong. There's a whole world of inaccuracies out there when it comes to R34 stuff (and probably 33 and 32). Lots of things that are 'just bolt on, entirely interchangable' aren't. Even between S1 and S2 R34's. Yes they have a GTT item supposedly being 296mm. This is incorrect. I would call whoever you got them from and return them and let them know the GTT actually uses 310mm rotors. Depending on where you got them from your experience and success will obviously vary.
    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
×
×
  • Create New...