Jump to content
SAU Community

Recommended Posts

it would be much appreciated if anyone can tell me where i can purchase a rockercover (valve cover) gasket for a RB25DET engine...as i have searched everywhere like autobarn, bursons, repco etc they only sell vrs kits (whole gasket set) and it's like about $400 and also timing belt, none seem to have a listing apart from repco, they were on back order got to wait till mid late next year i was told...phhhht what joke!!!

thank you.

Link to comment
https://www.sau.com.au/forums/topic/99296-rockercover-gasket/
Share on other sites

I go directly to Nissan for all my parts. Reasonable pricing imo for genuine parts.

Recently did my rockercover gasket for my RB20. If I remember right the rockercover gaskets and halfmoon rubber seals were a total of 70 bucks and for 20 washers was 40 bucks.

Good luck

$70 is reasonable but then again thats for a RB20...it might be more expensive for a RB25DET, i was told it had to come in from Japan..i tried asking the jap car mechanic shops, i even offered to buy it from them they were no help in pointing me to the wright direction....some C?NT even quoted me $770 just to change the rockercover gasket. "and i am 100% sure i heard him correct"

$70 is reasonable but then again thats for a RB20...it might be more expensive for a RB25DET, i was told it had to come in from Japan..i tried asking the jap car mechanic shops, i even offered to buy it from them they were no help in pointing me to the wright direction....some C?NT even quoted me $770 just to change the rockercover gasket. "and i am 100% sure i heard him correct"

Yer not sure about RB25 pricing but I doubt it would be much more expensive. Just go to Nissan and see how it goes, if you've got an asshole parts division at your Nissan who won't look after you because you have an import, give Gary Lechte Nissan (Frankston) a shot, they've been very helpful and friendly when I go in for my parts. Their number is 9782 2744. :D

mate i can get you the two rocker cover gaskets and the timing belt for $120 all up.

timing belt: 130285L327

rocker cover gaskets: 1327058S01 and 1327058S11

im in sydney but can send these parts to ur local nissan dealer for u to pik up if interested...

ALL PARTS ARE IN STOCK

Edited by gts25x

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...