Jump to content
SAU Community

Recommended Posts

First you use the search button :)

You will find this feature very useful for alot of questions about your car.

In the past month there has been a plethora of threads opened about r33's and oil changes and what oil to use, some I think even include pictures.

Most use Motul Turbolight 10W40 or similar, and the oil filter is a Z145A (Ryco).

Nath

Link to comment
https://www.sau.com.au/forums/topic/100015-oil-change/#findComment-1822804
Share on other sites

The how to:

http://www.skylinesaustralia.com/forums/in...showtopic=10035

I used Motul 300V Chrono 10/40 - quite expensive but it held oil pressure much better than any other oil i've used before and the engine ran very quite and revved quite freely. The cheap Ryco filters are fine to use.

-rb25

Link to comment
https://www.sau.com.au/forums/topic/100015-oil-change/#findComment-1826542
Share on other sites

How do you say its fantastic.  Most oils are fine.  Dump it at 5000km and replace it.  Its only after years of running you will know if the oil is great or not. 

Oil pressure on the stock gauge seems to be similar for most kinds of oil with my car..

It might be bs but i've noticed that different oils seem to lend different qualities to the motor - like make it run smoother and quieter, but thats just me...

Each to their own i guess, i would run a thinner oil if all i used the car for was round town work but my car gets heavy highway use and many hours stuck in peak traffic, so i wanted something that would give protection at the upper thermal range, and also with my car on 103,000km i doubt the clearances are what they used to be, so i opted for a thicker oil....in terms of protection you're right, i wont know for a while, but i do know that its working great sofar as nothing has broken yet :)

Link to comment
https://www.sau.com.au/forums/topic/100015-oil-change/#findComment-1828554
Share on other sites

Coz I just recently put Valoline 20w-50 XLD premium on my r33 gtst?

Arghhhhhhhhhh *Screams*

Please take the advice of the other guys and do not use cheap oil in your R33. It is worth every cent if you spend a little more each time you do an oil change.

Nath

Link to comment
https://www.sau.com.au/forums/topic/100015-oil-change/#findComment-1829841
Share on other sites

I reckon any semi synthetic that is from a reputable manufacturer will do the job. If you're religious with your 5000km service I wouldnt worry too much. If you extend it to 10000kms Id go full synthetic. I rather take the cheaper oil dump more often approach..probably in japan our cars were getting an oil change every 15-20k kms. 10k kms if by the book. As motors get older therre is more importance in doing the regular changes. It is all the unburnt hydrocarbons and petrol related products that get into the oil that cause further degradation of seals etc and decrease the effectiveness of the oil in lubricating.

Edited by benl1981
Link to comment
https://www.sau.com.au/forums/topic/100015-oil-change/#findComment-1829854
Share on other sites

I doubt any damage would be done by using thicker oil (20w-50w) but if youve got a newer engine you may as well take advantage of using higher quality thinner oils like 5-40 etc.

If youve got a bog stock rb30e with 200+ on the clock you wouldnt want to use anything other than 20-50 however due to the clearances rings etc being worn. Too thin oil will cause the motor to lose compression due to it slipping past the rings etc.

Link to comment
https://www.sau.com.au/forums/topic/100015-oil-change/#findComment-1832330
Share on other sites

Motul 4100 and a Ryco filter every 5,000km is all you need to know really :O

benm i will spank you if i catch you putitng turbolight in your new GTR. 4100 is a very cheap oil and is not a full synthetic oil. it is a blended oil. go at least for the 8100, but i would say use the Chrono 300V.

I've used the castrol forumla R 10W60 and personally i think it's too thick. a good full synthetic around the 10W40 area is what you want.

Link to comment
https://www.sau.com.au/forums/topic/100015-oil-change/#findComment-1837837
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...