Jump to content
SAU Community

R33 GTSt - 12.4 @ 123 MPH!!!!!!


Recommended Posts

What's in it

RB26 HKS Motor with two all beef patties (HKS 2510's), pickles (forged pistons), sauce (very big injectors), lettuce (HUGE HKS FMIC), cheese (HKS Cams), on a sesame seed bun (twin plate clutch, dog box and mechanical diff...)

That about cover it??

But wait there's more... lots more I just CBF typing....

R32PWR (aka RoundEye) here,

Thx to tha good Doc drift for being my support crew on the lovely evening.

Yes, the R33 is nuts .. it has heaps of potential.

My 1st run was 13.6 (very :P after that), but eventually reached a respectable 12.4 @ farrrq! .. I was also fortunate to come runner up on the 8 car shootout (luck of the draw).

My plans are to soften the suspension, lose the 2" catty, slicks, more boost (ran 1.3 bar on 12.4 pass), and try dragging without a .2 - .3 headwind.. I would expect low 11's to be feasable :D:)

for those in the market for a complete car built for track (this thing has $6,000 Climax suspension, nismo bushes, etc (not good for drag) - then email me or even phone [email protected] / 0421 058259 if your interested. I'm looking for around 30k for my ultimate sleeper GTSt with fully worked Rb26dett.

Stay tuned for my next session, and also the dyno figure following Dr Drifts Dyno day (22nd Feb and every month there on).. aiming for over 300rwkw's.

Cheers,

RounEye

There should be an easy mid 11 there, maybe low 11 - have a look at the time vs mph for my bike in my sig, and that was with ~2.1 60'. I raced a GSXR600 that ran 123mph, it did 11.5 iirc.

Anyway enough of my dribble, congratulations on the time, car sounds like a beast :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
×
×
  • Create New...