Jump to content
SAU Community

Boost Gauges Cheep Vs Expensive

StOjA

By StOjA,
in Engines & Forced Induction

 Share

Recommended Posts

7yphon Experienced

7yphon

Posted
Posted (edited)

No you should just watch it over time tho the cheap ones dont always last too long, A mate of mine brought a cheap Boost Gauge and his lasted a month. Then it started to creep off, My HKS Boost Gauge on the other hand is still going strong and it came with the car.

So I guess you get what you pay for.

Edited by 7yphon
BronzeMFP Rookie

BronzeMFP

Posted
Posted

Greddy makes a nice electronic boost gauge. I currently have one in my car, it reads boost accuratly and responds quickly. Where as my buddy had an autometer gauge that would read 5psi when the car was off :blink:

Al Grand Master

Al

Posted
Posted

I have found the Apexi Boost gauge to be great.

But i was considering getting 3 cheap gauges, for temp and pressure, for $220 or the DEFI DIN-gauge set for $600.

I know Defi are accurate and will last for years. But i am thinking; even if the cheap ones are inacurate, you only need to know where they usually sit and be worried if this changes. But now i read that these cheap gauges do alter their readings with time :O.

Is this the case for both mechanical and electric gauges? As i am only getting the electrical type.

Mr. Oizo Grand Master

Mr. Oizo

Posted
Posted
I have found the Apexi Boost gauge to be great.

But i was considering getting 3 cheap gauges, for temp and pressure, for $220 or the DEFI DIN-gauge set for $600.

I know Defi are accurate and will last for years. But i am thinking; even if the cheap ones are inacurate, you only need to know where they usually sit and be worried if this changes.  But now i read that these cheap gauges do alter their readings with time :).

Is this the case for both mechanical and electric gauges?  As i am only getting the electrical type.

And the Apexi ones look the best too! :O

boost.jpg

Al Grand Master

Al

Posted
Posted
yea apexi rocks but cant find one under $275 ...

Nengun: Click Here

OR

RMS Motor Parts Pty. Ltd.

Unit 3 / 662 Whitehorse Road,

Mitcham,

Victoria, 3132,

Australia

Phone: (03) 9872 6669

Fax: (03) 9872 6697

Emails:

General Info : [email protected]

Sales : [email protected]

Trading Hour:

Mon-Fri 10AM-6PM

Sat 11AM-5PM

MearCat Proficient

MearCat

Posted
Posted

I would also recommend VDO. If you're not after a fancy dial face and only after functionality, VDO is the way to go. Autospeed did a review and found that the VDO boost gauge was good (Avg error of 2.5%).

To quote Autospeed :

"Indeed, VDO offer good value for money while perhaps lacking the frills and panache of some. Accuracy is up there, and thanks to the German company establishing a manufacturing facility here in Australia, warranty isn't a problem. VDO gauges are available from most outlets and the range of hardware is extensive."

Funnily enough, there is one for sale on Ebay right now :Ebay VDO Gauge

Why spend $240 on an Apexi gauge when a $80 VDO gauge will do the same without having to worry about the accuracy/reliablity of something like Speco. I'm like having Functional stuff in my car, not into bling so I bought a VDO.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...