Jump to content
SAU Community

Recommended Posts

I went for a bit of a spirited run up a windy road in my completly stock, apart from zorst, R32 GT-R. The oil temp got up over 100 maxed around 105. The oil is fully synthetic mobil 1 variety. I was just wondering wat is the maximum temp I should let the oil get to before I should start to worry about bearings e.c.t. Also on the way down the windy road the brake pedal disappeared to the floor which was an interesting experience they came back 15 mins later presumably when they cooled down. Would some exotic brake fluid help this or should I just upgrade the brakes if I continue the windy road drives. :rolleyes:

Link to comment
https://www.sau.com.au/forums/topic/101051-oil-temp/
Share on other sites

When it starts getting over 120 degrees, start looking at oil coolers and with the brakes, yep brake fluid will help & a good set of pads. Try the Motul RBF600 brake fuild & RB74 front pads with comp2 rear pads.

Another thing is don't ride the brakes, what I mean is brake and then take your foot off as any friction will build up heat.

Link to comment
https://www.sau.com.au/forums/topic/101051-oil-temp/#findComment-1844680
Share on other sites

Pick up the phone, dial the freecall number to Mobil and speak to a techo. You should find that a full synthetic is designed and rated to easily withstand 105 deg C temps.

If that's the max you get, little to worry about especially for a road car getting limited thermal loading.

If you want to run track work, oil coolers are an easy way to achieve more consistent temps and reliability.

Link to comment
https://www.sau.com.au/forums/topic/101051-oil-temp/#findComment-1845831
Share on other sites

Trust me it was a very sprited drive up hill with plenty of full throttle accelleration, hard braking then back on the throttle repeatidly for a solid 20 mins. I wanted to find the limits of my driving and the car. The part I love about the gt-r is it is so easy to drive it hard, I very really find myself in a situation where i'm out of control.......so I need more power lol

Link to comment
https://www.sau.com.au/forums/topic/101051-oil-temp/#findComment-1850112
Share on other sites

I am curious about the opposite - How cold is too cold? Curious at what point I need a thermostat on the oil cooler

And where are you guys taking the measurement from?

Look at it this way - the stock oil temp gauge on a GT-R is in the range of about 70 degrees to 150. If you are just cruising along it settles at about 90 degrees. So you would infer that 90 degrees is a good aim point for the oil temp.

Link to comment
https://www.sau.com.au/forums/topic/101051-oil-temp/#findComment-1889790
Share on other sites

Fanging it hard at >120C for a long period is no good because the oil thins rapidly and wouldnt provide an optimum film thickness to maintain good antiwear properties. Anywhere between 80-110C is safe but if your oil is constantly under 60C, or it takes more than 10 minutes to reach 80C, I'd definitely be thinkin about getting a thermostat.

Edited by Busky2k
Link to comment
https://www.sau.com.au/forums/topic/101051-oil-temp/#findComment-1889999
Share on other sites

Interesting this oil temp subject. I circuit race a 32 Gts-t 2.2 with 235RWkw ans using MOTUL 300V chrono 10/40 ($$$) and a heap of Greedy top of line elect gauges, big trust radiator and 9 row oil cooler (originally mounted behind RH guard). First outing last Sept and oil got to 115, water 88. Told this was too high - so moved oil cooler behind intercooler.

Next race (bit hotter day) and different track - oil peaked at 225 and water 100 for most of day.

Before next meet, I heard that up to 130 Ok, so left oil cooler where it was due to lack of time.....but put in some air deflectors - still ran at 125 and water about 95 all day.

About 50ml of oil in catch tank over 3 meets. Oil still looks and smells good.

At "brisk driving" (about 80% on track) oil stays at a steady 88.

Hope this all helps abit.

Kerry

Link to comment
https://www.sau.com.au/forums/topic/101051-oil-temp/#findComment-1892251
Share on other sites

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...