Jump to content
SAU Community

Recommended Posts

hi guys

about a week ago i changed my rocket cover gaskets and now there are leaking and pissing oil everywhere in my engine bay. i have change it and used gasket maker to make a better seal but no good. has anyone had this problem and how did they fix it?

cheers

bill

Link to comment
https://www.sau.com.au/forums/topic/101338-rocket-cover-gasket/
Share on other sites

If its at the rear its probably comimg from the 1/2 moons , did you change them ?

the oil was leaking from the back. where can i get the half moon rubber seals from? would they sell them at nissan? if so anyone know the Serial number for that part?

cheers

bill

Curious to know where this comes from:

rocket covers

As has been pointed out, it is actually rocker cover (probably more correctly 'cam cover' in this case as there arn't any actual rockers).

Anyway, only the rear 'half moon' seals require some sealant at installation. The rocker cover gasket requires none - just make sure it is 'square' in the groove of the rocker cover (no twists, etc).

Curious to know where this comes from:

As has been pointed out, it is actually rocker cover (probably more correctly 'cam cover' in this case as there arn't any actual rockers).

Anyway, only the rear 'half moon' seals require some sealant at installation.  The rocker cover gasket requires none - just make sure it is 'square' in the groove of the rocker cover (no twists, etc).

It comes from the old cars that use to have rockers .

You dont need any sealant on the rubber that goes in the groove , they never leak , most times you can even reuse them and they dont leak if installed correct.

If you think they are hard to seal, how would you go with old cork gaskets ?

It comes from the old cars that use to have rockers .

'rocker' does, 'rocket' doesn't AFAIC (and I've been around 'a while')

You dont need any sealant on the rubber that goes in the groove , they never leak , most times you can even reuse them and they dont leak if installed correct.

If your saying the half-moon seals don't require sealant I disagree.....and so does Nissan. OTOH, the rocker cover gaskets themselves don't need any sealant

If you think they are hard to seal, how would you go with old cork gaskets ?

[sigh] I don't think the are hard to seal at all. As for cork.....come back and talk to me when you've worked on a veteran car......

steveL ,

I meant you dont need sealant on the rubber gasket but as i said earlier i use some on the half moons where they mate with the cil head case .

I have worked on some old cars in my time, i have been around for a while and i owned a very quick EH Holden many moons ago .

I had a quick VK...whats ya point...

And yes I agree with the above, re the sealant only on the half moons, use that orange stuff (name evades me at this moment).

Also when tightening the covers bolts/screws to them in a similar fashion as you would putting a head on, that is night tighten them around in a circle, and fully tighten first go, this will ensure that the mating surfaces are meeting square!!!

  • 6 months later...

Just replaced the right cam cover gasket, the rubber washers and the 'D' seal for the first time and all I used was $10 silastic from Autobarn only on the top and bottom of the 'D' seal and tightened the screws till the washers started to 'balloon' slightly. Been 4 weeks and so far so good.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...