Jump to content
SAU Community

Intercooler Installs?

Shado34

By Shado34,
in New South Wales

 Share

Recommended Posts

Shado34 Explorer

Shado34

Posted
Posted

Hey all

Just got a hybrid intercooler for my r34 gtt. So far ive been quoted $350 for install, does anyone know if this is a good price or if there are any places where i can get it cheaper etc looking for north shore preferably but dont mind a drive for a cheaper install :P

also i was told by one place that hybrid intercoolers are hard to install and hit the fan or something on r34's anyone know about this?

tnx B)

Link to comment
https://www.sau.com.au/forums/topic/101368-intercooler-installs/
Share on other sites
Mr_G Mentor

Mr_G

Posted
Posted
Hey all

Just got a hybrid intercooler for my r34 gtt. So far ive been quoted $350 for install, does anyone know if this is a good price or if there are any places where i can get it cheaper etc looking for north shore preferably but dont mind a drive for a cheaper install :P

also i was told by one place that hybrid intercoolers are hard to install and hit the fan or something on r34's anyone know about this?

tnx  B)

Hey champ, ive done tonnes of r33 and some r32 installs of those hybrid kits, but havent done a 34... PM me and we can organise, and ill def beat that price you been quoted :D

Since this will be my first 34, will prob charge a flat price, but should be the same as 33 etc, as it all ligns up the same, only diff in ligning up might be some of the holes :)

Let me know if your keen

Mr_G Mentor

Mr_G

Posted
Posted

I completed Shado34's kit yesterday. Its abit diff to the 33 as you have to drill 2 extra holes on the support bar. You also need to remove the window washer bottle as it gets in the way of the piping that runs to the intake.

Other than that, I found that more of the fan blades need trimming, and that the piping running to the belmouth of the turbo was very very tight!!! Other than that, install went good. Hope your happy with the work champ

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...