Jump to content
SAU Community

Took The Stag To Drags Last Night

AlexCim

By AlexCim,
in Four Door Family & Wagoneers

 Share

Recommended Posts

AlexCim Grand Master

AlexCim

Posted
Posted

Well, all you guys know my Stageea and basically whats done to it.

I have split front/dump from batmbl, $440 catco cat from him too, fuji catback (very quite, with mid muffler), FMIC (not really power mod), pipercross panel filter (again, minor) and was using 10psi of boost....all untuned. These are all my power mods, the rest is all chassis/handling :P. So its not TOO far off a stock car, mid mods.

Not sure what power to expect with that, but i think somewhere around the 140awkw mark maybe? Just because the catback is really quiet, its also a tad restrictive. No worries to me.

So, the runs I did were

Run 1:

2.475 60 foot

[email protected]

This run was my first ever at a drag strip, i was peaking. I made some mistakes rushing things and got a poor launch. Also, O/D was off

Run 2:

2.139 60 foot

[email protected]

This was text book. I didnt rush at the lights, reaction time was 4 seconds because i was spooling. Handbrake on, till it was creeping... launch!

Run 3:

2.414 60 foot

[email protected]

....I launched and forgot the handbrake on.

Run 4:

2.196 60 foot

[email protected]

Again, this was a good launch, built boost, o/d was on for run 2/3/4 as it seemed better.

So, best was 14.7@92mph

Not too shabby if I say myself. Standard SS's and XR6T's were just not able to crack into the 14's, they were doing low 15's. So... there we go.

Anyone else want to post up a list of mdos and also ET's and trap speeds?

I went to the drags to test my car pre manualizing.

Ill post up in this thread when i get my car dynoed pre manual and let everyone know my power. Then after the manual ill chuck it on the dyno and let everyone know my power, then off to the drags again. But this car isnt being modded to going in a staight line, remember that, but it will sure hold its own on the street...specially in the wet.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/101824-took-the-stag-to-drags-last-night/
Share on other sites
AlexCim Grand Master

AlexCim

Posted
  • Author
Posted

No too sure what it was stalling up too. It was probably around the 2500-2750 RPM range.

Because I didnt do a burnout, i had a long time to stage. So id roll up, stage, gear 1, handbrake, hand on release, get ready, wait for other guy to stage, stall, booost boost boost, handbrake/brake off, floor it, hand on gearstick, shift at 6k

BoyWhoCriedWolf Grand Master

BoyWhoCriedWolf

Posted
Posted

Well done Alex, some good times there! I put the Stag on the rollers (pfc had dramas so is not installed) and got 202 at the wheels. I will be running it down the strip in a couple of months when the season starts again.

Ska Grand Master

Ska

Posted
Posted

Well done alex! my old r33 with ~180rwkw I took to the drags just before I sold it and best I could crack was a 14.1, but that was mainly because I am crap at the drags and wheelspun most of the way, but still, 14's is a great time!!

I cant wait for mine to be tuned then I'll be off to the drags to see what it can do :)

Might be an idea to start a new thread, just for 1/4 mile times. We have a sticky thread like that in the qld section, which works well as you can then post up what you got then later down the track after mods post up again and see the difference and compare with other times.

Be nice to have one just for stageas :)

Well done again alex!

ian Experienced

ian

Posted
Posted

Alex, do you still have the standard ECU? If so, you should have taken a laptop and dumped what everything was doing over the 1/4.. If you go again give me a yell, as I can lend you a laptop and cable (and my software is just about done.. :-)

Ian

AlexCim Grand Master

AlexCim

Posted
  • Author
Posted

Stock ECU, stock auto box with my screwed torque converter (it woo's a lot, since my going in revserse down a hill when in D)

I want to weigh the car soon, see what it is.

We should start a 1/4 mile thread, but i dont think anyone/only few others have been down the 1/4..?

ian Experienced

ian

Posted
Posted
Stock ECU, stock auto box with my screwed torque converter (it woo's a lot, since my going in revserse down a hill when in D)

I want to weigh the car soon, see what it is.

We should start a 1/4 mile thread, but i dont think anyone/only few others have been down the 1/4..?

When are you heading out to do it again?

Ian

AlexCim Grand Master

AlexCim

Posted
  • Author
Posted

As soon as i can find someone selling a bloody r32/33 GTR gearbox with transfer case and shifter, + 2 weeks labour.

But at this point, ill have a powerFC so no logging etc...

I am sure it isnt too different to some midnight action on a country road, we can arrange something one night before manualizing?

ICE12 Collaborator

ICE12

Posted
Posted
I am hoping so! It weighs 1703kg dry and no driver so that will hurt a bit.

Ken let me know when you are going as I will take mine along for some fun. We could race and I then could tellyou how good your car looks from behind, that's if i can see that far a head of me, LOL.

cheers ICE

BoyWhoCriedWolf Grand Master

BoyWhoCriedWolf

Posted
Posted
Ken let me know when you are going as I will take mine along for some fun.  We could race and I then could tellyou how good your car looks from behind, that's if i can see that far a head of me, LOL.

cheers ICE

First round of the drags, thought I might take the missus car down too and get someone else to drive it.

Dont know when the first round is though?????????????

beastien Proficient

beastien

Posted
Posted

Ian, I've looked into a daughterboard for the series 1 stagea ECU, and it's similar to the R33 ECU, so it doesn't have the 40 pin header :)

But i've found it does have an external eprom on the mainboard which has external connection points.

We just need to find someone with the knowledge and skill to nut it out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Butters
      UniClutch

      By Butters · Posted

      Well they got my money but they are not getting my gearbox ! 
    • GTSBoy
      ECU sees many times the speed than speedo does (R34 swap)

      By GTSBoy · Posted

      It's needed for rolling idle up, and I think it is a decider on VCT also.
    • Kinkstaah
      ECU sees many times the speed than speedo does (R34 swap)

      By Kinkstaah · Posted

      I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...