Jump to content
SAU Community

Recommended Posts

Hi All,

So now I've signed up to get an import thru Geoff@Prestige.....

Your advice/comments/experiences on which is better would be greatly appreciated ! Stock ?? or Modified ??

Here's my 2c:

Stock-

Pros: Not thrashed(maybe), You get what you see

Cons: Expensive to mod, once here

Modified-

Cons: Could have been thrashed, lots of worn out bits

Pros: Let someone else pay for mods - get good value for $$$

Thanks all , you've been heaps of help so far !!!

BF

Link to comment
https://www.sau.com.au/forums/topic/1033-importwhats-betterstock-or-modified/
Share on other sites

most of them are thrashed whether they have mods or not.

i got my car with heaps of mods and saved a stack. i've seen ppl buy stock cars for the same price that i got mine and they are even older cars in some instances.

put it this way, after buying my car i wouldn't have $15k to spend on mods so i'm gratefull the previous owner spent that amount. who cares if they are slightly used, you save more than enough to pay for your insurance for a few years.:P

Well it depends on your situation, if you've got plenty of many, then buying stock and modding wouldn't be a bad idea. But if you're working on a some what limited budget, i would probably looking the best car I could with the most mods, if the car's been kept tidy, chances are it's been looked after somewhat by an enthusiast. If the car looks trashed, it's probably been thrashed.

But if you're buying a modded car, try and budget that little bit extra for the un known. And the other thing with buying a stock car, just because it looks stock, you could also run the risk of it not being looked after/serviced regularly.

That's just my opinion, but I think going through Geoff you'll get a pretty good idea of what the car is and has and needs.

I think everyone that goes for an import is trying to save $$ and at the same time get value .

What it comes down to (as birty says) is : How thrashed do these cars get ?? Is a mod'd one more thrashed than a stock one ? How can you tell ??

Is 'thrashed' the same here as it is in Japan ?? How do the japanese get to thrash their cars ?? Streets ?? Drags ?? Other ??

Does thrashed mean 'abosolutely buggered' or does it mean that it has had some hard traffic light hero yards ??

Lets look at WORST case scenario... highly mod'd car (that is obviously not a drifter or race car ie: no roll cage, normal suspension etc) - Can the Japenese get away with some of the stuff we can get away with (eg: no speed limit in NT, bad roads) ?? Can they do it constantly ??

Or do they just put heaps of mods on their cars to show off - and maybe do the odd burrrn here and there ?

I spose the answer is : "it depends"...

It's an educated guestimate lottery !!

BF

Originally posted by ONARUN

most of them are thrashed whether they have mods or not.

i got my car with heaps of mods and saved a stack. i've seen ppl buy stock cars for the same price that i got mine and they are even older cars in some instances.

put it this way, after buying my car i wouldn't have $15k to spend on mods so i'm gratefull the previous owner spent that amount. who cares if they are slightly used, you save more than enough to pay for your insurance for a few years.:P

Yeah but your mods were done locally dude!

Brendon, in japan most cars are either bog stock, worked and used as drifters/racers, or worked to "look like" drifters or racers. I doubt a stock car is going to be thrashed, normally geoff can tell you about the condition of the inside ie worn rubbers on pedals, worn carpet and seats, and wear on gearknob and wheel which are a BIG indication of abuse.

Stock is best if you can afford to mod later, of course buying modded can have drawbacks like the cost (additional) to remove performance parts and refit when compliancing, however several people have bought their cars in modded and found extra goodies such as different turbos they didnt know about or other hot bits which is a nice surprise.

As you mentioned, geoff does a good job in supplying ALL available info about the cars history/condition to the prospective buyer so you are on a winner with him.

my 2 sence plus GST long time :(

Really depends on what you want.

I chose stock because I wanted to understand what each modification did, and and what works and what doesn't.

But if you just want a gutsy car, get a modded one and save the money.

And like everyone is saying, all these cars have been thrashed. Any performance car has, after all, what else are they good for???

I chose to get a stock car for the exact reason you said Brendan, i was *hoping* that would mean it hadn't been thrashed.

The only thing changed in the car was the stereo. Everything else was original...the interior was immaculate (except for a slightly worn steering wheel), it had the original Skylines mats, and even the flare....and the jack & spare wheel look like they've never been touched. So i guess I got what i asked for.

But, as GTR-80Y said, next time I would be looking for one with minor mods. Just a few things like an exhaust, maybe a body kit etc, stuff that adds up in $$$$ here, but doesn't really cost more when buying at auction over there.

One with heaps of mods, i would stay clear of, but that's just me :P

Either way the car has may have been thrashed. If the car is still running fine and checks OK with mods its probably a bargain. However, I've seen cars that were "not modded" even though there were tell tale signs like mounting marks on the dash and extra holes in the engine bay.

I agree with all the people that would get a modded car. Not only do you save on all the goodies but you get the techinical expertise that has gone into it.

A car built here and a car built in japan will never be the same. Generally the car that was built in japan will have complementary gear and will suit a purpose.

Geoff seems to have good suppliers who checks the cars out well so I would go with a modded one also.

It's not uncommon for a modified car to have ALL the performance parts removed (quite often some without a trace!) So how then do you know if your stock example really is/was stock & wasn't trashed?!?!

I've seen the above happen to cars once they've arrived in Australia. Yards do it sometimes as it easier to move a "stock" import, rather than try to sell as is. Potential buyers are more wary of a modified car, as per shell's last paragraph in her post above.

My 2.2c

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...