Jump to content
SAU Community

Recommended Posts

An atmo bov will increase the backfires as its venting air to the atmo instead of back into the air intake making the afm compensate with more fuel, which means car runs richer and backfires. It used to happen on 90% of my gear changes so I got rid of the atmo bov and went back to the std one, though when I downchange at 3000rpm or more it backfires too. Need to get an SAFC to lean it out a bit.

Ive always had it, figured the aftermarket ECU caused the majority of them. Then i got an atmo BOV and its increased slightly, probably hear 6 or 7 in an hours worth of driving. Doesnt really do any harm. ALOT of turbo nissans do it with aftermarket exhausts.

But if its doing it on 90 percent of your gear changes then thats just ridiculous.

And its not strictly a backfire in my opinion.... backfires cause people to hit the pavement (see Uncle Buck).... Skylines seem to just make nice snap crackle pop noises.

Red17

yep, i believe that this 'backfiring' as described is actually 'over-run'. I think it has something to do with the fluid (exhaust) flow through a pipe and the effect of massive changes in flow velocity as you change gears (i.e very fast gas flow to much slower)... sort of a reverberation within the pipe. This happens more with aftermarket exhausts due to the increased diameter resulting in a greater flow speed differential. Of course if your mixtures are rich then this will also cause exhaust noise as the unburnt fuel is ignited outside the combustion chamber.

This is only a guess, but i think it is reasonable given the aerodynamics i studied through my (unused) mechanical engineering degree... feel free to correct me if i'm wrong.

OK...youve given me some ideas...thanks.

Some great theories, and it's intriguing that others suffer the same problem.

It is actually a popping noise, rather than a backfire, still, it is a bit distressing. Is it damaging though ??

I do have an aftermarket exhaust...a Kakimoto NS309....but the problem has only recently started....possibly after I was stuffing around with the BOV tension.

I might try tightening up the BOV (an atmo) and see if that has any effect.

cheers Ozzy

same here ED!

The Skylines are known to run very rich. Up the boost and the ECU over compensates even more. Mine is starting to sound like a rally car on the up changes ( running 0.9 bar ).

Could be wrong but I definately though it was unburnt fuel from running too rich.

BUT it sounds COOL...RIGHT???

Maybe not 90% of your driving time tho, that'd be a little annoying! I can get mine to back fire any time usually, just nail it and the back off real quick, if no back fire, lightly tap the Loud Pedal and you should hear the fruits of your labour.

I think my plugs need replacing now, but that's OK...

Yeah its just a pop, not a huge backfire... yeah its cool, there is one corner on the way home if I get the green light I can wind it down from 80km/hr to around 40km/hr and drop it into 2nd and I got a nice pop out the back... I suppose if I had a dump+front pipe and no cat I'd get flamage :P

I bet if you put the standard BOV back on you wouldn't hear a sound...

Yes the ECU expects an extra burst of air from the plumb back which is expelled from the intake system, so it compensates for this by adding fuel. This also solves the mystery of why some after market BOV make your car stall (over fuel).

A mate of mine solved this by installing an AVO atmospheric/plumb back BOV (all in one).

But if you don't mind the sound, forget about it, it's doing any harm.

Have Fun.

Yesiree, it is mine.....thanks....I think it looks good too. It came from Japan like that....I believe it is a standard factory R33 GTR bar.....Its good in several ways....you can remove the bottom lip when its been scratched to hell and repaint it off the car....(the beast has Tein's all round and is set on the stops)....it also allows you an absolute shirtload of room for a FMIC....which will come when the MRS lets me spend some more (of my) money.

cheers Ozzy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity.
    • 100% the factory sender is tapered, that is how it seals (well, that and teflon paste or tape)
    • Thanks folks - I've saved a few links and I'll have to think of potential cable/adapters/buying fittings. First step will be seeing if I can turn the curren abortion of a port into something usable, then get all BSPT'y on it. I did attempt to look at the OEM sender male end to see if it IS tapered because as mentioned you should be able to tell by looking at it... well, I don't know if I can. If I had to guess it looks like *maybe* 0.25 of a mm skinnier at the bottom of the thread compared to where the thread starts. So if it is tapered it's pretty slight - Or all the examples of BSPT vs BSPP are exaggerated for effect in their taper size.
    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
×
×
  • Create New...