Jump to content
SAU Community

Sneaking Past The "turbo" Law


Recommended Posts

Xinhua why do you have to come down here every weekend you only need a some sort of mail to go to your bros house and thats about it or if he puts you on the lease it is even better. but you shouldnt have to come down every week end

  • Replies 69
  • Created
  • Last Reply

Top Posters In This Topic

I highly doubt the RTA would hire a private investigator to follow some 17 year old kid around. They have multi million dollar road development projects etc to worry about before they get to you.

Just don't drive like a tool or modify your car to attract attention to yourself and you should be fine.

Lol.. I'm stock and have a gts.. I got pulled over 4 times in one night and followed a few times, mainly cause I was on quiet roads I guess, but still, sometimes you gotta take the quiet roads.. and they are pretty consistent with me.. blah blah where's the turbo, 5 mins of explains it's a gts.. Then them probably double checking everything.. They will... check you.. if they see the red P plates..

So what if i have 18" chromes, exhaust, lowered and a custom plate? whats illegal about that? why do they pull me over..

18" wheels are 2" over the maximum factory supplied wheel diameter.

Exhaust may not meet the DB levels for ADR's, and your catalytic converter could not be functioning properly allowing illegal levels of CO into the atmosphere.

Lowered suspension could make the lowest point of the car below the ADR approved limit, coilover suspension is illegal in most states where not supplied by the manufacturer etc

There's a million and one reasons that could be used to pull you over. Keep in mind they only need to suspect something is amiss on your car to pull you over and question you or inspect your car. The less reasons you give them, the better obviously.

i never get pulled over, and even when i do, they dont bother with anything... my secret...

NO FULLY SICK EXHAUST TIP OR BLOW OFF VALVE that immediately pisses off coppers.

if u get caught driving it, just make up an excuse saying you got no car other then the GTST and u need it to get to work and bacl, otherwise ur gona have to turn to the doll without the vehicle.

Edited by Alien
How many people have been pulled over for a stockie GTS? does it get annoying? and what do you say to the cop?

Cops can't tell that it is a GTS though mate, remember that. Until they physically look under the bonnet. They don't know.

..And even then they still ask "Where is the turbo?" -_-

Stock looking GTS would still probably get you pulled up, especially with cop magnets such as a huge loud exhaust and massive rims.

Obviously the more stock it looks, the better for police sake.

You sure? :cool: I have heard that its defectable

Some cops may defect you for it, but that's mainly because they don't know the law and want to give you a hard time.

The RTA's VSI 06 (guidelines on light vehicle modifications) say that your replacement wheel may not be more than 25mm wider than the largest rim for that vehicle, and the track cannot increase by more than 25mm, while still being classed as a "user certified" mod or in other words something you don't need an engineering certificate for.

It says nothing about the diameter.

I believe that in the RTA's implementation, "widest rim for that vehicle" is the widest rim listed on the tyre placard. Victoria has a similar law, but the "widest stock rim" is based on the chassis (if I remember the article in Motor Magazine's "Hot Tuner" editions correctly). So in NSW a Commodore Executive can have a rim 1" wider than the SS' while still being legal, whereas in Victoria the same car can have a rim 1" wider than a HSV's.

All I remember for certain about that is that Victoria's laws were more generous than NSW's.

Some cops may defect you for it, but that's mainly because they don't know the law and want to give you a hard time.

The RTA's VSI 06 (guidelines on light vehicle modifications) say that your replacement wheel may not be more than 25mm wider than the largest rim for that vehicle, and the track cannot increase by more than 25mm, while still being classed as a "user certified" mod or in other words something you don't need an engineering certificate for.

It says nothing about the diameter.

I believe that in the RTA's implementation, "widest rim for that vehicle" is the widest rim listed on the tyre placard. Victoria has a similar law, but the "widest stock rim" is based on the chassis (if I remember the article in Motor Magazine's "Hot Tuner" editions correctly). So in NSW a Commodore Executive can have a rim 1" wider than the SS' while still being legal, whereas in Victoria the same car can have a rim 1" wider than a HSV's.

All I remember for certain about that is that Victoria's laws were more generous than NSW's.

Thakns for that :geek:

And.. furthermore.. I wonder how many people actually got skylines ( turbos ) when they were 17..

I'd imagine the majority got them around 19-20ish when they had some money etc..

I got my turbo r33 when i was 17 and learnt till i got my P's.....very hard to maintain at that age

So what car are you getting xin?

In other news I pick my car up on Friday after being off the road for.. around 5ish weeks or more I think.. :) Can't wait! I organised a new front bar with my repairer and am looking forward to seeing what it is :mad:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...