Jump to content
SAU Community

Recommended Posts

yes a stock GTR is around 180 - 200kw on most dynos. a few kw more with exhaust etc.

i would go.

boost controller (run 1 bar boost)

apexi pods in a custom box

3 inch cat back exhaust

front pipes

dump pipes

Power FC

cam gears (both inlet and exhaust)

and you will get around 240-260rwkw if everything is working properly

i would also do your brakes (new pads, rotors, fluid) and add an oil cooler.

Just got a 90 model GTR?

The first mod you should be doing is a major service.

True, at least all fluids, tyres (if you imported it) and a check over and clean.

After that, drive it around for about 2 months to see if you can 'feel' anything wrong with it before modding.

Also, I got mine dynoed before I did anything to see what the power and boost curves looked like and see if they held steady or spiked/dropped off.

Just got a 90 model GTR?

The first mod you should be doing is a major service.

This goes without saying (but ill say it anyway), change all the fluids - you dont know when they were last changed......if at all.....

i just got a R32 GTR as well, leaving it stock for the moment just to see if there is anything wrong. Don't wanna spend all the cash modding then if something goes bang, your in trouble. Unless money is no issue :P

I've put in a set of XENONs though, but it doesn't go any quicker :D

Edited by gexenon

Just keep the boost at no more than 15psi with the other things mentioned above and you should be fine

And yes, that power (260) will happen with the mods mentioned above, unless theres a problem with your engine

yes a stock GTR is around 180 - 200kw on most dynos. a few kw more with exhaust etc.

i would go.

boost controller (run 1 bar boost)

apexi pods in a custom box3 inch cat back exhaust

front pipes

dump pipes

Power FC

cam gears (both inlet and exhaust)

and you will get around 240-260rwkw if everything is working properly

i would also do your brakes (new pads, rotors, fluid) and add an oil cooler.

Mine has all that less those couple of things and does over 250rwkw. Also need rising rate fuel reg. Plus for that boost level steel wheeled turbos is a handy insurance. I lost a good engine to a blown ceramic turbine as the crap often gets forced into the cylinder causing nasty damage.

Additional to all other suggestions I recommend the timing belt/pulley bearings be replaced ASAP as well as new grade 8 bolts for the bearings.

  • 5 weeks later...
sweet got more replies than i thought

im definatly doing the full fluids change and i was planning to wait a while before trying to get more hp

another question for yas

can my 32 get 240 -260 and still last a while or is it prone to go bang????

I can only tell you of where i went

100K service, doesnt matter if its got 98K or 50K on the clock, you will have a sound base to work from

Redline fluids

Brake fluid

3inch exhaust

front pipe

power fc

boost controller (1 bar)

Adjustable cam gears (both)

= 250rwkw

+ some drag racing

= "hey whats with all the smoke and where is all the power!" (Damn ceramic wheels!)

IMHO Whatever you do be realistic about your expectations and consider the risks.

I dont know your circumstances but if you want to start spending cash on it by all means go nuts.

I did; now i'm asking the forum questions about mods on a 300rwkw combo and contemplating the rebuild next year

....but if you dont, get the service, get a new stereo (is that what young ppl are calling them these days?), fix stuff that becomes an issue

and enjoy driving it for a while...After all it's a still a GTR

Edited by Mr. Keets

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...