Jump to content
SAU Community

Recommended Posts

Hi all,

This is a new thread started from the original e.o.i. from this thread:

http://www.skylinesaustralia.com/forums/in...pic=109132&st=0

Overview:

Anyways, as some of you know or will know (after reading the above thread) - I am in the process of designing and making custom kickplate inserts for all the Skyline models. I have seen all the various shapes and sizes from the R32-R34 and can say that factory black kickplate looks a little bland. After seeing n15m0's thread, I took it upon myself and a few others to design something nice to dress this part up.

It's the first thing you see when you open the door to your car, might as well make it nice. Just open the door of say a BMW M3 and you'll know what I mean, makes it look that extra bit classy.

Product:

After giving it some thought and contacting a few suppliers both domestic and abroad we came up with the following:

* New kickplate "inserts" that will bolt onto the existing unit/s on all Skylines

* Made of scratch proof Titanium (coated using PVD process)

* Finished in Gold, Silver or Black (plating process)

* Light weight, durable and most of all aesthetically pleasing.

* Item that can be DIY installed with minimal fuss / skill

* Item that can be customized to the client (laser etching whatever they want)

Designing:

I took the kickplate off my R34GTT and measured it up using various items then transferred all the information I needed into a CAD drawing. Everything that needed to be measured for fabrication was done. Had a little trouble getting the "SKYLINE" text from the internet for use, so spent another 4 hours measuring that up as well.

End result was a detailed 2 page CAD drawing with enough information for my suppliers overseas to make me a prototype. The first prototype will be for my R34GTT and will be done using the Ti - Silver finish. Once I am confident that the design is flawless and requires no further change, other models will be measured up for fabrication.

Models to be Covered:

Skylines R32 to R34 (both 2 door and 4 door variants, GTST and GTR - depending on demand)

Stageas

Cefiros

* Just makes more sense to do Skylines first as I'll have access to my own kickplates ;)

Costs:

To be addressed after final quotation and prototype has been sent back... but as a basic guideline using common sense:

* Basic price will include Silver plated plates for a 2 door using generic etching pattern

* Custom etching will attract a premium

* Gold plating will attract a premium

* 4 door variation will attract a premium

Requirements:

Obviously I'll need the kickplates from each model to do the initial measurements. I'll be contacting members with specific vehicles and ask to borrow their items. Or like Tangles has done, I'll be accepting offers items in exchange for the product measurement to be made up.

Another thing that is needed (which is now sorted) is the text/font to be used on the plates. Initially this won't be a problem but later on, with people wanting custom designs - this could become an issue.

Timeline and Progression:

11/03/06 - Idea is conceived by n15m0

16/03/06 - Concept taken onboard by myself as potential fabrication product

20/03/06 - R34GTT kickplate taken off for measurement

21/03/06 - R34GTT design sent to overseas supplier for quoting and prototype fabrication

23/03/06 - Cefiro added to the design list

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

For those who don't know what the laser etching outcome will look like, here is a photo of an item I found on Google. Everyone must've seen this process on some product once before, it's actually a very popular process...

post-19974-1142999223.jpg

All it is, is a laser set to a certain frequency burning the top layer/s of the metal hence creating the difference in tone and texture as compared to the original material. Saying this, if someone was to provide me with a multi-layer image (say CF pattern) - etching such a thing would be no problems at all.

They are not a direct replacement for your existing kickplates... they are only metal plates that you integrate onto your existing items.

We've gone for an adhesive solution for now, but once the prototype returns we'll come to a final decision then. Maybe we'll have to opt for some type of screw or rivet to hold it in place properly.

Another idea thrown around was a "send us your kickplates, we'll install, then send back to you" option.... or even an exchange programme.

A lot of options here... have to wait till the prototype returns before any further decisions are made.

Being measured up this week, 32GTR and hopefully 34GTT 4 Door.

Can anyone confirm that the GTR kickplates are identical to the GTST kickplates across all three models?

If this is the case it will save me a lot of time :P

Pretty please somebody?

Oh yes... I forgot about them (sincerely sorry) - if someone is willing to send me some Cefiro plates, I will definitely get them done up as well :P

Sorry dangerous_daveo - no beef :D

Great idea Stan, will be very interesting to see how these turn out.

I can check on friday night, whether or not R32 and R33 gts-t and gtr ones are the same if you want.

I'll be in for a set for an R32 GTS-t 2dr for sure.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...