Jump to content
SAU Community

Recommended Posts

so read this thread for probably half my day. I can summarise it down to this

1. One of the middle oil feed is blocked and a restricter is put on the rear (VCT equiped RB25NEO)

2.Fitting an oil drain at the back of the head

3. Port matching the oil galleries to the gasket

Now there has been a discussing earlier in the thread regarding the side to which the placement of the drain line from the head to sump should be located. Mspeed/Japs seem like they're going via the intake side whereas SK suggest going via the exhaust side with the drain above the oil level. So up to this date which way would be sufficient for a street driven car with occasional track days. Didnt quite get to see a good conclusion between the two ideas. Or is there a better method for having a bit more control to the oiling issue and breathing.

The external head drain is not a drain. It is a vent to prevent sump gases having to come up through the in block/head drain. Thus preventing the gases from preventing the oil draining, if you get what I mean.

I think ill just stick to getting a bigger baffled sump and maybe put restricter with no drain. Ive read nearly the whole thread and actually more confused.

You're almost there - follow Simon's example in the post above yours. Actually the bigger sump and restrictors will cover most of it. But while you have the sump off drill and tap (or weld if you're so inclined) two fittings as high as possible on the intake side of the sump. You can just cap or plug them for now and if you decide you need the two breathers later at least you won't have to pull the engine out again.
  • Like 1

Ok, Confused as hell right now, I have an RB25 that will be running a few track days, (drift/circuit) It has a Nitto oil pump, crank collar, 2 x 1mm restrictor's, So do I run the oil drain from the back of the head to the cold side, high on the sump above oil level, rocker cover breather's to a catch can, catch can drain back to sump aswell? do I put a breather on the catch can? (Also need the car to be street legal) Will this work? I'm about to pull the motor to fit the oil drain in the head, Would like it to stay there once I put it back in :)

Ok, Confused as hell right now, I have an RB25 that will be running a few track days, (drift/circuit) It has a Nitto oil pump, crank collar, 2 x 1mm restrictor's, So do I run the oil drain from the back of the head to the cold side, high on the sump above oil level, rocker cover breather's to a catch can, catch can drain back to sump aswell? do I put a breather on the catch can? (Also need the car to be street legal) Will this work? I'm about to pull the motor to fit the oil drain in the head, Would like it to stay there once I put it back in :)

You don't need the fitting at he back of the head. Two lines between the sump and a catch can would be good - one at the top of the can one at the bottom so it can drain if necessary. Follow the post above from Simon. To be street legal over here (and I suspect it is the same in Aus) you can't vent to atmosphere which is why I run a line back to the turbo intake. If you suspect there is excessive oil fumes in that line (a properly baffled catch can will hopefully prevent that) you will need to run a second catch can or oil/air separator in the line to the turbo intake
  • Like 1

So just about to add some -10 fittings to my stock sump and noticed that the ribbing in the sump only has just a few tiny holes for oil before it has to go over the "dam".

Wondering if anyone else has added any extra drains?

post-16200-13882869140376_thumb.jpg

post-16200-13882869384274_thumb.jpg

simon is this a custom catch can or a purchased one with some mods or brought like this? if so where from

To do one better I just had my fittings welded today so I have photos :)

Sump on intake side is 2 x -10

20130921_135621_zpsa08b89e1.jpg

Catch can has one -10 drain at bottom that will go to the sump, 2 x hose tails on top to go to cam cover breathers and one -10 that will go to the other fitting on the sump as a vent.

661b9f1b-8133-4ace-a4b5-50b5dcaaa0bf_zps

You are best to get one custom made as very few off the shelf items have any proper baffling inside. Mine is plumbed the same as Simon's except where he has a vent I have a line going to the turbo inlet.

You could buy a 4L square surge tank and cut it up and modify it to suit.

http://www.ebay.com.au/itm/Oil-Water-or-Fuel-Catch-Can-or-Surge-Tank-Alloy-2-0L-/251408805028?pt=AU_Car_Parts_Accessories&hash=item3a8921eca4

Heya guys,

Massive (and multiple) breather tanks are overrated.

If a tank is baffled correctly (and has an oil drain), it can easily be under 1L capacity and feed clean air to pre-turbo in a closed loop system.

This makes mounting easier and forces some thought into the actual design of the baffles.

I'm not about to wax lyrical about air/oil separators or throw in my 2c about RB oil control as it's all mentioned in this thread at some stage or another.

But if you want to solve (or bandaid as best as possible) the issue and are in Sydney, PM me for a chat if you're bored.

Mark :)

So just about to add some -10 fittings to my stock sump and noticed that the ribbing in the sump only has just a few tiny holes for oil before it has to go over the "dam".

Wondering if anyone else has added any extra drains?

attachicon.gifImageUploadedBySAU Community1388286733.000952.jpg

attachicon.gifImageUploadedBySAU Community1388286757.667836.jpg

I drilled ours out larger and added a couple of extra holes.

I also tapered the in side (rear side) to help flow.

We also have 2 dash 10 fittings welded to the RHS on a high octane cast alloy sump extension.

What if a one way valve is fitted to the line draining from the cylinder head to the sump. This could the located as close as possible to the sump so that no oil ever goes back up to the head through pressure from the sump.

Just to clarify if you are draining back to the sump then it needs to be on the exhaust side of the block/sump. Inlet side will only ever vent.

Not while in vacuum?!?

Mine seems to be draining to the inlet, unless it's actually not filling the catch can in the first place any more.

Just to clarify if you are draining back to the sump then it needs to be on the exhaust side of the block/sump. Inlet side will only ever vent.

Not so. I have clear evidence that my catch can is filling up and draining. Anyway its quite impractical to run a drain round to the exhaust side.

Drain is easy. If paranoia about windage takes possession of your brain, just put the bottom end lower than the oil level. There isn't actual positive pressure in the sump that pushes oil up a drain into a catch can. If the catch can is up high enough then there is a head of oil to push it back down into the sump. That's kind of the point.

Too many people imagine too much half arsed physics when thinking about this stuff.

So just about to add some -10 fittings to my stock sump and noticed that the ribbing in the sump only has just a few tiny holes for oil before it has to go over the "dam".

Wondering if anyone else has added any extra drains?

ImageUploadedBySAU Community1388286733.000952.jpg

ImageUploadedBySAU Community1388286757.667836.jpg

factory those holes don't exist, they are drilled in there when after market sump baffles are fitted

No they (the ones under the 4wd shaft tube) are there in GTR sumps, albeit very small holes.

The idea is you open them up and add a few extra ones if you like to help oil drain back, the factory ones are tiny and struggle to keep up.

About the holes in the side of the sump on the intake side of the sump, they are pressure relief ports, no need to put the rear breather behind the head, your releasing pressure straight out of them so it does not travel upwards towards the head which fights the oil trying to travel downwards.

One of them can be used as a oil drain if run into the bottom of the oil catch can, blowby pressure when present will blow through the oil if oil is present in the can and still be a breather, when there is no crakcase pressure when driving normally or backing off it will flow back into the sump on that line.

One large fitting on top of the catch can can vent to atmoshpere or better still run the large line between your filter and turbo inlet, when driven hard there is some vacuum created there which will help draw the blowby gasses out of the catch can, helps to add vacuum to the catch can to enhance the blowby scavenging effect.

Some old school V8 setups even use to run a vacuum port off the exhaust headers, the line was welded in at a angle to the header for maximum scavanging effect, a one way check valve was used to stop backfire from going up into the breather system and this helped to assist creating a vacuum to draw blowby gasses, however you want to be sure you have a free flowing exhaust that does not have back pressure when attempting that one.

I see it cleaner and simpler to use the airfilter to turbo pipe as a vacuum port.

As proof there is a vacuum there, note GTR's have a spring wire inside the rubber intake pipes between the airflow meter and turbo to stop the pipes from sucking in and restricting flow because of the high vacuum level when the turbo draws air, might as well use the free scavanging effect to draw your blowby out of the crank case after its been through the catch can to remove all oil from it.

Edited by GTRPSI
  • Like 1

The only reason it wont be draining now is most likely because there is no more oil in there to drain as you have alleviated the blow by and oil control issue.

If it were going to be a drain it would only drain under no or light load situations, not under full throttle full power running.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...