Jump to content
SAU Community

Recommended Posts

let me get this straight

10% lower

so this car on any other dyno would make ......

319 divided by ten is 31.9 in case you dont know / cant work it out

319 by plus 31 would be 350

THREE HUNDRED AND FIFTY REAR WHEEL HORSEPOWER FROM A STOCK TURBO

does that even look remotely close to being right for you? dont dance around the question, answer it! does that look like something that would normally happen on a R33 Skyline powered by a RB25DET motor with minimal mods? just answer that, i dont want stories about corrections , timing, dynos, just answer me that

jesus snap out of the day dream!

Edited by [teejay]
  • Replies 164
  • Created
  • Last Reply

Top Posters In This Topic

Didnt realise that this thread was about Bretts car

the 53 degree inlet also seems pretty funny.

im not accusing anyone of anything or the like, my call here is that this thing must have hidden mods. you just need to find them.

End of the day Brett made his power 2 odd years ago, old news, lets stick to this other mystical freak 33 shall we?

Edited by [teejay]
All Dyno Dynamics Dynos should read almost identical results if in Shoot out mode? No matter what intake temp!

Wrong. Well, sort of. The inlet temp sensor has to be placed in such a way that it ACURATELY reflects the ACTUAL temp of the air entering the engine (usually before the filter).

u would think u work for xspeed or hyperdrive. give steve a break, he is only tuning it he doesnt know the exact details of the internals/mods. :)
^^^ i agree....Steve is only doing the job he was asked to do...maybe Teejay you should pay for the labour to find out what is in this car....then we would all know what 'mods' it has!!!

Ezz up on Steve he is a top bloke!!!!

Ive offered a free dyno run to confirm the figure... no reply as of yet. Would be on a brand new DD dyno , 4wd in ground, with the latest and greatest of everything.

I dont work for any performance shop, i work for the Water Corp, ... but i also work for Perth Street Car magazine.

Would make a really cool story "car makes amazing power with little mods"

Call my questioning of this "research" since i get sick of the crazy amount of people who will come and make wild claims like this (not saying this is!).

Ease up on who and why? Im not attacking anyone, I'm just incredibly keen to see a real answer to this mystery, not "oh it made the power its true, it must be" Im not questioning the power, just how its made. read my other posts to see where im coming from. Steve chooses, to answer, i choose to question, its all been done in a civil non rude / attacking / slanderous manner, so whats the issue?

I just want it played out to an honest answer. If it ends up being that its made the power with the stock turbo, ill applaud it.

Till then get your emo out of here, and let some interesting Skyline related talk keep going. Wasteland for you if you cant handle the skyline chat.

Teejay there is no emo from me...but Steve is only asked to tune the car not find out what mods it has to make the power....Its up to the guy to get someone to check out how it can make this power and as you put it snap out of the day dream or prove that it is from a stock turbo with min mods!!!

OK i cant back the 299.1 car yet but early this week a GTS with SAFC cooler and cat back made 292rwhp.Before you start it did go to the plex on wed this week.13.1 all night with a best of 13.0 I do think thats a WA Stock GTS record. Was the Silver S2 R33.Im getting a time card to post but the speed was about 180ks.As Rev210 said Track is proof.

We also have full Shootout 4WD dyno about to be fitted.

OK i cant back the 299.1 car yet but early this week a GTS with SAFC cooler and cat back made 292rwhp.Before you start it did go to the plex on wed this week.13.1 all night with a best of 13.0 I do think thats a WA Stock GTS record. Was the Silver S2 R33.Im getting a time card to post but the speed was about 180ks.As Rev210 said Track is proof.

We also have full Shootout 4WD dyno about to be fitted.

I was there on Wednesday night and can confirm the car did run a best of 13.08 from memory. I work with the owners girlfriend and was watching the car closely. I believe it still has a stock dump pipe!

Still on 235/45/17 road tyres (not drag rubber)

The ironic thing is that the owner was disapointed that he couldn't do 12's

Wrong. Well, sort of. The inlet temp sensor has to be placed in such a way that it ACURATELY reflects the ACTUAL temp of the air entering the engine (usually before the filter).

If you are a shootout workshop and running in shootout mode you must place the sensor at the air filter. Top Racing are shootout workshop!

All this talk of different Dyno's, and prove it on the track etc, really amuses me.

The thread title is........... 319wrhp Standard Turbo! (maybe).

You cannot prove any of this without dismantling the turbo. FULL STOP.

And any of you other guys with "freaks" should think about this.

I know my Turbo was "hi-flowed", as I had it done when I killed it (as stock) with too much boost.

I wonder how much anyone else knows how stock their turbo is ?

Will continue to watch this space with amusement.

El Bee

what was too much boost?????

The guage I had then showed 17 lbs a coupla times before it went.

I had built an Electronic Boost Controller was dialling it in with a gut full of piss and my Son at the wheel.

It may have been a combination of me fiddling with the load points and a lack of consistency in the runs.

Anyway, that turbo was certainly not a freak. It got 184 rwkw on a dyno day (maybe a bit friendly even).

El Bee

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...