Jump to content
SAU Community

Single Turbo Skylines

Guest Silver_GTR34

By Guest Silver_GTR34,
in Engines & Forced Induction

 Share

Recommended Posts

JimX Grand Master

JimX

Posted
Posted

It is easier and cheaper to get big boost happening with a single turbo. The main advantage of the two turbos is for better response low-down. If you're not concerned with this then there isn't much point having 2 turbos.

Of course, the twin turbo setup on the GTR is better than the single turbo on the GTS-t. But the GTR owners doing the single turbo conversion are usually bolting on one bigass $10k+ Trust turbo or the like, not a small turbo off a GTS-t :D

Doctor Mentor

Doctor

Posted
Posted

I dont know about the lag difference between using 2 smaller turbos and a larger single. From what people have said and tried, is that the single can be equally laggy if not better than the twins due to all of the exhaust going into the one turbo to hel pspool it up and not being halved to run two of them. Hope that makes sense, Im very tired!!!!

Leewah Veteran

Leewah

Posted
Posted

When I decided to do a complete rebuild of my engine, I decided to go a large single setup instead of a medium twin setup like a 2835 or 3037S for a number of reasons.

Primarily, price. With a TT setup, you have almost double the costs in dump pipes, wastegates and the like.

A single setup only requires one dump pipe and one wastegate.

Also the large single turbo is less laggy than the above mentioned twin setups. My turbo will spool at about 4300 and keep climbing past 8800. My rev limiter is currently set to 9000rpm in an effort to make the engine last as long as possible. The turbo itself is good for 35psi which would create as much as 500rwkw at the wheels in a GTR with the correct setup engine.

A twin setup such as the 2835s or 3037s setup won't spool till after 5000rpm unless you do a larger bottom end like Munro.

PA080028.JPG

predator Grand Master

predator

Posted
Posted

What about rigging up a sequential turbo setup to a GTR? Is that common, or too much effort? Wouldn't that overcome the problem of lag and give the best response over the whole range?

I'm talking about mainly Japan, because i know there aren't too many GTR's out here comparitively, probably even less modified.

JimX Grand Master

JimX

Posted
Posted

I think sequential turbos are largely a waste of time for a performance car. They only really improve driveability. They also lower your off-boost threshold so you'll probably find that you're always going through more fuel.

To overcome the disadvantage of not having a sequential turbo setup, launch from a higher RPM and keep the revs up.

Leewah Veteran

Leewah

Posted
Posted
Originally posted by brendanf

hoe lee fark that is a nice engine !!!!

Are you sure you couldn't have fitted a bigger turbo to that ???  

Appreciate the comments all.

Yes I could have gone a bigger turb than that but this one suits my hp requirements at the mo :D The only thing is that if I do go bigger now, I need a new manifold which positions the turb further forward. I do know of a car running the larger turbo and it's making 460rwkw on PULP on a base mapping :eek:

The turbo itself isn't actually a T88 but a Garrett equivalant which was custom sized wheel and exhaust housing to suit my requirements of a faster spooling turbo. The exhaust housing is the size of a T78.

where can i get an intake pipe like the one on there?

Call Unifilter and they can sort you out. That's a 5" pipe they usually fit to trucks.

Leewah Veteran

Leewah

Posted
Posted

Dude,

Obviously you weren't looking close enough to the 2 cars :P

Ben's turbo is BIGGER for one, his intake piping goes down through the chassis to the bottom where the indicators are on a stock front bar, and most importantly, his car is white!!

His rocker covers are black (used to be red), and his radiator shield is a stainless silver piece.

His intake plenum ain't stock. His catch can looks different. He runs Tomei cam gears.....

Should I go on???

:shake: :shake: :shake: :shake:

Originally posted by INASNT

dave isent that engine pic of one of bens cars from race pace??

i have seen that engine bay in the flesh and your car in the flesh and things dont add up :confused:

:shake:
Guest INASNT

Guest INASNT

Posted
Posted
Originally posted by Leewah

Dude,

Obviously you weren't looking close enough to the 2 cars :P

Ben's turbo is BIGGER for one, his intake piping goes down through the chassis to the bottom where the indicators are on a stock front bar, and most importantly, his car is white!!

His rocker covers are black (used to be red), and his radiator shield is a stainless silver piece.

His intake plenum ain't stock.  His catch can looks different.  He runs Tomei cam gears.....

Should I go on???

:shake: :shake: :shake: :shake: 

:shake:

hehehehehe, smart ass!!

i always thought u had twin low mount turbos on yours?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...