Jump to content
SAU Community

Recommended Posts

Finally got one, I didnt really think it would make much difference, but coming down hill braking, the pedal stayed were I started, there was none of that bit of fade when stopping, feels normal really and mighty glad I did it.

I took a fully detailed drawimg of it before I installed it, but after starting a new job, I cant really fabricate any yet, but if some one wants them or can plot into autocad give me a PM.

I would redesign it so the nut is in front of the plate.

post-17300-1143705712.jpg

Link to comment
https://www.sau.com.au/forums/topic/111740-brake-stopper/
Share on other sites

I've seen them attached to the spring mount as well, I imagine that they would be for a track car more so than a streeter, plus the threads may not be long enough with the cusco bar there but it would make good template for it.

Link to comment
https://www.sau.com.au/forums/topic/111740-brake-stopper/#findComment-2062454
Share on other sites

Finally got one, I didnt really think it would make much difference, but coming down hill braking, the pedal stayed were I started, there was none of that bit of fade when stopping, feels normal really and mighty glad I did it.

I took a fully detailed drawimg of it before I installed it, but after starting a new job, I cant really fabricate any yet, but if some one wants them or can plot into autocad give me a PM.

I would redesign it so the nut is in front of the plate.

I have got something similar that came on my strut bar. Only mine isnt bolted on to theside of the engine bay like yours..... didnt have any bolts handy and there were not any holes (and didnt want to go drilling willynilly). It seems to hold rather firmly and i dont have any brake fade which is good for when i get pressing pretty hard going downhill.

Link to comment
https://www.sau.com.au/forums/topic/111740-brake-stopper/#findComment-2062481
Share on other sites

omrae

The locknut doesnt fit in there, no room.

REdgtst

The holes were allready there with nuts/thread in them as standard on mine.

Wink

Yeah but I can always point to and say have you got one of these? HaHa!

Link to comment
https://www.sau.com.au/forums/topic/111740-brake-stopper/#findComment-2063411
Share on other sites

Bad thing about these is that pretty soon you get used to the feeling and it doesn't make a 'difference' anymore.

It does when you heel/toe on your downchanges, which I do pretty much all the time as it is smoother. with the flex in the firewall you need to adjust the brake pedal that much higher to overcome the travel before you start to contact the accelerator. This is for the style I use, but if you are double jointed then it's not much problem with it standard (eg Gan San in the BMI videos). Also braided lines and good pads make a huge difference, along with slotted discs.

Link to comment
https://www.sau.com.au/forums/topic/111740-brake-stopper/#findComment-2063897
Share on other sites

Nah didnt make it, but want to, they are a fairly simple piece to make and if I could get them plotted into autocad I can get them profile cut, which is 70% of the work, then just got to source the cup bit on end of bolt.

Drawing not to scale. gotta love Paint.

brake_stopper.bmp

Link to comment
https://www.sau.com.au/forums/topic/111740-brake-stopper/#findComment-2064802
Share on other sites

  • 1 month later...

I made my first prototype today, had a drawing and cut up the steel then lost the drawing, I assembled and welded it from memory, only to find it was opposite hand, lol, I now have an example of what not to do hehe, and can get them painted in acid etch black, I still have to find a cup for the end, its something to do in those slow times.

Link to comment
https://www.sau.com.au/forums/topic/111740-brake-stopper/#findComment-2198764
Share on other sites

Here is another one I made (the right way this time) I changed from 8mm bolt to a 10 and put it in the flat instead. If you live in SEQld and want one PM me $15, I will discount for club members $10, supply will depend on work loads and demand. I still cant find the cup and looks to be a bit pricey so they wont have them, I wanted to make them out of stainless but my new job doesnt have the materials or equipment and its more a bling thing anyway.

someonestolecc

You can do it!

post-17300-1148635529.jpg

post-17300-1148635575.jpg

Link to comment
https://www.sau.com.au/forums/topic/111740-brake-stopper/#findComment-2205535
Share on other sites

I tired to do a cad drawing but i am missing a dimention. The one that shows the distance form the bottom main plate to the righ hand side. The one on the right is 22mm but i need the opposite side. Also i have modified it a littel so once finished i will post it up.

It looks good. I had to fuge some of the mesurments. I have got a qute to get these laser cut and it will cost about $5 for each item and about $8 in SS.

Link to comment
https://www.sau.com.au/forums/topic/111740-brake-stopper/#findComment-2205620
Share on other sites

Just for the R32 owners.

I dont know if this will fit a 32 or what a 32 one looks likes. if you have one on a 32 give me look.

On a side note, one of my workmates told me about repairs he did to fords, he had to weld the master mount back together on quite a few and this mod was added.

Link to comment
https://www.sau.com.au/forums/topic/111740-brake-stopper/#findComment-2206161
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...