Jump to content
SAU Community

Recommended Posts

  • Replies 194
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I will be coming on the night but won't be dynoing the car. I 'estimate' that I'll be answering many questions and meeting many people.

Everyone will make at least 296rwkw with their SAU sticker. Can you please bring mine on the night Karen? I want it for the drive home lol.

As for no two dynos being the same...that is why Shootout mode was developed, so that there would be consistancy between dynos no matter what the ambiant temps or air densities were.

Good to see your coming Dan...

Guys one week to go... Dont forget the actin starts at 6pm..

Ill be there with both cameras and will cut a small clip of the event to help cross promote the night with the club...

OK UPDATE:

I have been and visited the workshop and meet Richard in person. I have to say it looks great. Their workshop and work eithic is awsome.

We have more parking room then you can poke a stick at. We will have plenty of standing room for the dyno. Plus the boys their know their rb engines well..

While i was there they were dyno'ing an r32 GTR. Stock as a rock with a simple cat back exhaust and an AVC-R installed (runing 0.9 bar) and it hit 230rwkw... So that sounds to be to be about right to me in terms of a true figure.

They had 5 skylines in their workshop and a VL turbo and a couple of S15's in the nissan family. On top of that they had 4-5 cars out the front also booking in for work. These are busy boys, their workman ship looks good to me and they are very friendlly.

Anyways i am happy about the location and hope to see all of you next thursday night.

IMPORTANT: Please look at the updated map in the very first post. Its easy to find once you get there. Is set back from the road in an industrial area. So we can make lots of noise.

Thanks Col

NOTE: Richard thinks we may be able to squeze a few more cars on the dyno and any R33/34 gtr's that want to run. Richard will drop your front drive shaft for you and put it back in (10 minute job with a hoist).... So the guys on the list are going on the rollers and maby a few more if there is time...

Cheers Col

I would estimate that i would be putting out stuff all, but a stock car would do that really. :) not going to embariss myself.

My car is 100% stock, I just want to see what I am starting at, see the graph so I can compare it with future mods. Now most people cant laugh at you cause their cars started stock once.

Heya guys...think i will pop by and have a lookie at the event n meet up with fellow skyliners...will i be able to dyno my car if there are available slots? :D
I totally forgot bout this thread! Count me in if theres a free spot! Eitherway will be there...

Jon

Yeah guys the list is full but do not worry... Richard said we will run as many as possible...

Just turn up and if there is a drop out or time to spare you guys will be more than welcome to run...

Cheer Col

Dont forget guys we need some of you there from 6pm... Ill be videoing the event and taking pictures to cut togther for a promo dvd....

I will a be a spectator for this one, got to renew membership Karen.

See you there.

Would organizing a meet up for the southerners be outa the question?

I'd be in for a meet up on the southside....will need to get a head start though to beat the peak hr traffic...

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...