Jump to content
SAU Community

Recommended Posts

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

8000rpm and side step the clutch, hangon, grab 2nd, hangon again, don't forget their is a hairpin at the end of the straight :D

Haha, I'll keep the hairpin in mind. :) What rpm do you usually launch at?

Be nice to 3rd tho.

3rd is evil and must be punished!

Ask me to race it ;)

no, no and no. :angry:

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2116006
Share on other sites

launching at around 7000 should be plenty. if you need more then try another 500 or so the next time. personally i wouldn't side step the clutch, but just let it out as fast as your foot can move back up off it. will be a bit kinder and you should still get 1.8sec 60ft. i'm no expert though, so probably a good idea not to listen to me!

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2116727
Share on other sites

Hey all,

I have spent my fair share of time on the track doing circuits etc but never run the 1/4.

What hints / tips do you guys have for my first run in the GTR tomorrow?

Thanks all,

Christian

Hi Christian, my tips would be:

1. Drive around the water if you dont want to do a burn out.

2. leave you window down a bit and tell the starting guys thats its your 1st time. They will show you where to stop. It's offen hard to see where the line is, and you don't won't to be floundering around reversing and going forward until the staging light go on.

3. Bring your rev's up to about 6500-7000rpm and hold them there. (depends on what power you have and how good your grip is). You dont wont your rev's to be too low or you will bog down off the line).

4. Lift you foot off the clutch until you feel it take, and then wait until the green lights, then lift off all the way, and then launch the thing.

5. 2nd gear change will come very quickly, so try not to bounce it off the limiter too much.

6. change at about 8000rpm.

7. When you go over the finish line keep your foot down all the way over the line. You will probably have to change into 5th going over the line.

8. Don't put your foot anywhere near the brake......just use the gears to slow down. (I've done this and I slid all over the track)

Also.........you don't need to go as soon as you see the green, just take your time. The timer starts when you cross the starting line.

This probably sounds all straight forward. I am a very conservative Drag..er...So, I hope some of the advice sounds ok. :w00t:

Stacey (the smarter and more consistant part of DiRTgarage)

Edited by DiRTgarage
Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2116924
Share on other sites

Thanks Stacey, that helps a lot. How far is the run off after the line?

Yes , I think it's more than the lenght of the track. You will have plenty of time to slow down. On my 1st go I ended up with my front wheels in the 'sand trap' (it's actually all rocks and gravel), so try and avoid that if you can.

And yes, have fun as it is a really good buzz. Also another bit of advice I tell people is to keep it as simple as you can. I always seem to be consistant with my times becasue I dont have much to worry about or remember to do.......other than launching. Reducing the amount of things you have to switch on/off or spin before hand is a good thing. IMO. :)

Hope it's not raining in Sydney.

Cheers..........Stacey

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117023
Share on other sites

From WSID:

"The WSID facility is a full international standard drag strip, built to current NHRA specifications. The braking are is 600 metres of asphalt, with a 120 metre gravel trap and catch net at the end. The track is 70 metres above sea level at the start line and approximately 66 metres at the finish line."

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117035
Share on other sites

Yes , I think it's more than the lenght of the track. You will have plenty of time to slow down. On my 1st go I ended up with my front wheels in the 'sand trap' (it's actually all rocks and gravel), so try and avoid that if you can.

And yes, have fun as it is a really good buzz. Also another bit of advice I tell people is to keep it as simple as you can. I always seem to be consistant with my times becasue I dont have much to worry about or remember to do.......other than launching. Reducing the amount of things you have to switch on/off or spin before hand is a good thing. IMO. :)

Hope it's not raining in Sydney.

Cheers..........Stacey

Awesome, thanks! :O

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117054
Share on other sites

I was shitting the first time i raced - was at the old ECRaceway main straight. BUT by the time I got into 3rd gear it felt natural and safe.

You'll be right but it's handy to have someone walk out onto the racing surface and show you where to stage so you don't roll through the lights and stage with your back wheels (I did this once @ ECR). Trust me you look like a dick when you do this :)

For some reason they don't let you get a 3/4-GTR lead on the line :O

Don't forget "The Book" either!!!! <----- single most important thing to remember.

Adrian

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117067
Share on other sites

Thanks Adrian, yeah it'll be good to have a chat beforehand as I said, I'm nervous as hell.

Christian

I reckon talking about it anymore than you are will just make you more nervous. Just line up on the line (little white lines either side of your lane), wait for the green light, foot on the throttle and brake once you go past the big digital timing displays. Treat it like a traffic light grand prix and you'll be right.

Most people have trouble just finding the start line (how I have no idea) so dont even try doing a 12sec pass on your first run, just get to the finish line, grab your time slip and line up again.

Edit: I'll be there just after 6pm as always, look for me in the hotdog line :)

Edited by benm
Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117072
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...