Jump to content
SAU Community

Had A Minor Mishap And Hit The Kerb :(

NateR31
 Share

Recommended Posts

NateR31 Grand Master

NateR31

Posted
Posted

So it was went, kinda lost it, front left mounted the kerb at around 40kms..

Now the front left wheel sits arounc 1cm further or so back, had a look under the car and nothing apears to be bent, but somthing is as the wheel sits back. I made a template of the right lower control arm to compare to the left and it seems fine. So what could be bent that dosnt look it? could the sway bar be pushing it all back?

any ideas?

just so you know whats there, the front is basicly the same as a s13/14/15 silvia

Link to comment
https://www.sau.com.au/forums/topic/116603-had-a-minor-mishap-and-hit-the-kerb/
Share on other sites
MerlinTheHapyPig Mentor

MerlinTheHapyPig

Posted
Posted

swap castor rod from other side, see if that fixes it, if so replace castor rod & get a wheel alignment probably a good idea also...

I came off a ripple strip sideways and bent front left upper control arm, we measured camber and +1.5 degrees before i replaced it!.......

NateR31 Grand Master

NateR31

Posted
  • Author
Posted
swap castor rod from other side, see if that fixes it, if so replace castor rod & get a wheel alignment probably a good idea also...

I came off a ripple strip sideways and bent front left upper control arm, we measured camber and +1.5 degrees before i replaced it!.......

hah! good idea! ill definetly do that today, thanks mate!

D_I_F Grand Master

D_I_F

Posted
Posted

your going to have to get it on a hoist or jax it up.. take the wheel off..

it could be a number of things.. castor rod, upper control arm or lower control arm.. i did the same thing with mine.. the front wheel was completely f*cked.. the back was a little off.. it was the lower control arm on the back that i had to replace.. just make sure nothing is leaking

ob1 Community Regular

ob1

Posted
Posted

My wife ran up a gutter in a similar way in my GTIR and bent the lower control arm. I just took it to my local Fulcrum shop and they diagnosed it for free. They didnt charge me 'cause they knew i'd be back at a later date with the control arm to pay them to put it in and wheel align it.

I'd say just duck down to a suspension shop and get them to check it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, plenty of air flow, there is a dedicated path that feeds the air in to the OEM intake tube behind the bumper As for a "tangible effect", maybe, but getting the pod/intake air out of the hot engine bay is worth it psychologically to me, even if it gives no performance difference, so the tangible effect in my Lizard brain saysss yessss  In the end, to me a tangible effect isn't always about performance, sometimes it a sound or a look, or even a...... feeling  Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Duncan
      NC MX5

      By Duncan · Posted

      Quite right, if you make it to that pension you deserve every cent
    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
×
×
  • Create New...