Jump to content
SAU Community

Recommended Posts

Have a look at the fun way in which the spindle (Vertical arm) has moved forward

relative to the upper link - about 3mm. Apart from killing my caster

adjustment it has barked the upper arm & squeezed the rear bush & ferked

it. This is on the LHS ie the unloaded side at the track. Haven't had

time to check the other side.

How can I stop this from happenning again?

post-5134-1147227295.jpg

post-5134-1147227316.jpg

Edited by djr81
Link to comment
https://www.sau.com.au/forums/topic/117148-stuffed-new-front-bushes/
Share on other sites

i'm guessing it's the effect of running lots of caster. dont know how to stop it other than to run less. :teehee:

hmm i was going to use bushes in the upper arm to, but having seen that i may replace it with an adjustable, rose jointed arm. it may be harsher but at least i wont end up with a 'dynamic wheel alligment'.

LOL...i get about 18 months from a set, i always thought it was because i tend to let them run a little dry, but your look to be all nicely greased up?

My current set have only seen abotu 6 months of driving, with about 12 months of the car sitting around, but will be tryign the Noltec upper arms when these ones die (which they will)

but will be tryign the Noltec upper arms when these ones die (which they will)

yeah that's what i was thinking brisby. but wont they suffer the same fate? they are the ones that are in two halves right? and one half slides in and out of the other (for the camber adjustment), but they still have urethane bushes at each end.

hmmmmmmmm

when i got a few things done on my car and recent wheel alignment, I asked for 9 deg positive castor. They said they could only go 7 deg because they were worried about the control arm bushes. now i see what they were worried about!

..... anyway, i don't care, next alignment, i'm going 9 deg. it's worth replacing the bushes every 6 months!!

hmmmmmmmm

when i got a few things done on my car and recent wheel alignment, I asked for 9 deg positive castor. They said they could only go 7 deg because they were worried about the control arm bushes. now i see what they were worried about!

..... anyway, i don't care, next alignment, i'm going 9 deg. it's worth replacing the bushes every 6 months!!

Up to you, but I wrecked the bush during the course of one track day. At $300 per kit plus fitting I can think of better ways of spending my money. :)

Guess I am going to have to wind out some caster.... :thumbsup:

Interesting...i suppose check the basics like the bolts were torqued up enough...properly lubricated, the upper arm is actually round and not elongated...they were the correct part number???

I dunno, i know i have had problems with them as well, never one track day though, but yeh i get about 25-30,00kms from a set...which in my eyes is nto that flash :thumbsup:

From fitting these parts myself all i an say is they dont go back in as easily as they came out :)

However they will fit and do work a charm.

Reading they are only going to last 25k isnt that crash hot though :)

When i have tha car on the wheel aligning machine they are a pleasure to adjust ;)

Caster is maxed out around 7 with the whitlines bushes if it means anything to anyone. :thumbsup:

I have already sent a PM to Richard on this subject, to summarise............

Check the travel, the only time we have damaged a camber bush on the track was when the suspension travel wasn't sufficient. The bottoming out on the bump stop transmitted the load to the bushes. The next closest flexible medium.

The old faithful "cable tie on the shock shaft" test of travel is the easiest method to determin if that is an issue.

There is a limit as to how much caster you can run, the radius rod bushes in the Group Buy kit are pretty close to the limit when adjusted to their maximum positive caster position. From memory Richard is using adjustable caster rods with spherical bearings, this means 2 things;

1. It is possible to exceed the limit of distortion that the upper and lower control arm bushes will tolerate. In extreme cases, the lower control can actualy bind at the pivot point in the front subframe.

2. Any impact is passed on by the inflexible radius rod and transmitted to the attached suspension components. This being the upper and lower control arm bushes, once again being the next closest flexible medium.

Double wishbone suspension in not like MacPherson strut, where you can wind on as much caster as you want. Distortion of the upper control arm has to be considered. What I would do to check the level of distortion;

A. Remove the wheel and the shock/spring unit and disonnect the stabiliser bar links

B. Set the caster and camber to the desired settings

C. Jack the suspension up and down and watch the upper and lower control arm distortion.

D. Adjust (back off) the caster such that the distortion is at an acceptable level

>_< cheers :angry:

The suspension travel issue sounds spot on...my cars springs had some issues which meant a lower then usual ride height...at the track i was hammering the bump stop with a front ride height of 315mm...the dead control arm bushes coincide with this issue...which didnt get identified and fixed until the installation of the latest set...a bit slow identifying the spring problem.

So with the new Cusco castor arms and Noltec upper arms what would be the ballpark castor setting...as i have been told thats why im struggling in slow corners with the 4-5 caster i have with the Whiteline bushes

The suspension travel issue sounds spot on...my cars springs had some issues which meant a lower then usual ride height...at the track i was hammering the bump stop with a front ride height of 315mm...the dead control arm bushes coincide with this issue...which didnt get identified and fixed until the installation of the latest set...a bit slow identifying the spring problem.

So with the new Cusco castor arms and Noltec upper arms what would be the ballpark castor setting...as i have been told thats why im struggling in slow corners with the 4-5 caster i have with the Whiteline bushes

Let's start with the Noltec upper arms, Greg knows this, so I am not speaking out of school.

They slip, they rely on the friction of the bolts (small) to hold the two parts of the arm together.

Fairly quicky the bolts work loose from the twisting plus end loads and they start sliding.

There is another design around, similar to the Noltec upper arm, but with a longitudinal retaining bolt and 2 nuts that prevent the halves from sliding over each other.

215 mm front ride height is definitely an issue, as you have identified.

We don't have any problem with achieving 6 degrees caster and 3.5 degrees negative camber, using bushes in the radius rod and the upper control arms. Getting to 4 degrees negative camber and maintaining 6 degrees caster is tricky though. You can get more caster by spacing the upper arm inner mount rearwards at the chassis mount. The bushes protrude from the arms by 20 mm. So you trim 5 mm from the rear bush and use 5 mm of washers between the front bush and the mount. This moves the top mount of the upright rearwards 5 mm, giving more caster without loosing any camber.

Using these sorts of settings will increase the loadings and cause premature wear of the upper and lower control arm bushes. No one said motor racing was cheap.

>_< cheers :angry:

We don't have any problem with achieving 6 degrees caster and 3.5 degrees negative camber, using bushes in the radius rod and the upper control arms. Getting to 4 degrees negative camber and maintaining 6 degrees caster is tricky though. You can get more caster by spacing the upper arm inner mount rearwards at the chassis mount. The bushes protrude from the arms by 20 mm. So you trim 5 mm from the rear bush and use 5 mm of washers between the front bush and the mount. This moves the top mount of the upright rearwards 5 mm, giving more caster without loosing any camber.

Using these sorts of settings will increase the loadings and cause premature wear of the upper and lower control arm bushes. No one said motor racing was cheap.

>_< cheers :angry:

I have looked at the design and wondered about that...so it can/does happen?

Also whilst i may regret moving away from the offset bush approach which has served me so well, knowing that i have been able to get 3-3.5 neg camber and about 5 degrees of caster with the bushes...i cant ignore the fact that every car i have driven with rose joint caster arms (Nismo/Tein etc) have all turned a lot better then my car. I was hoping the Noltec solution to adjustable camber was going to be the solution, hoping that such arms had been R&D by plenty of club/circuit cars....

I hate this, i was thinking about actually making my own upper arms to the required length to get the camber i need...i know the Nismo arms work in a similar fashion

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...