Jump to content
SAU Community

Recommended Posts

Wrecking R33 GTST series 1.

* RB25DET..damaged sump, crank pulley, turbo has small hole, cam sensor, timing cover, a/c & power steering pumps PRICE DROP $700

* Passenger side door complete with trim and glass ****SOLD****

* Brake master cylinder $50

* Series 1 computer $200

* glove box $50

* Centre console with lid slight bend at front $20

* Centre vents $50

* Rear tailights black in colour *****SOLD*****

* Rear bar has some damage $150 black in colour price drop $50.. *****SOLD*****

* Front calipers with pads complete $200 *****SOLD****

* Rear calipers with pads complete $200 ****SOLD****

* Rear hubs with handbrake cables $150 ****SOLD***

* Rear bootlid with GTR wing no lock in boot $300

* Front seats $150 each

*Rear seat $100 complete

* Cluster with 76,000k's..broken tabs where screws go $70****SOLD***

* GTR style rear bar with pods to suit $300 *****SOLD*****

* Interior trims from $10

* Front disc rotors ******SOLD*****

* Rear disc rotors $50 pair*****SOLD*****

* Diff $200

* Tailshaft $100

* Rear hicas unit $100

* Power steering rack $100

* Engine crossmember $100

* Front hubs $100 pair

* rear windscreen with hole for wiper ****SOLD*****

* rear 1/4 windows $100 each

* door handles $25each

* Aerial unit $50 *****SOLD*****

* roof lining $50

Plus more..please PM for details or photos etc.

Located in sutherland shire.

Thanks....

Edited by sav
Link to comment
https://www.sau.com.au/forums/topic/117817-wrecking-r33-gtst/
Share on other sites

  • Replies 90
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

ok try answer everyone questions.

* Sorry dont have a/c condensor

* i may sell wing without boot if wing comes off easy enough..i will have a look tomorro night.

* as for the brakes had a lot of interest in them so $600 as apackage..still good just checking the pads but i have 2 sets of rotors so will sell with the best ones.

* Sorry sooley this is the same one as before gearbox sold already

* the tailshaft snapped at the yoke but looks ok still..has the shaft then uni and broke after that $40.

i Mate,

Assuming the front brake rotors fit GTST series 2 I'd be interested.

Could you send close up photos of rotor condition

Cheers

David

0414-232497

[email protected]

Edited by stealth
hey dont no if still available but interested in both rear hubs without discs and without calipers just the hubs are they available.

also is the power steering pump available

i have power steering pump though pulley i damaged $50

hubs sold sorry

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...