Jump to content
SAU Community

Recommended Posts

pineapples work well in reducing any rear cradle movement...which helps eliminate axle tramp...also the likely hood of the shocks being gone in a car os this age should be pretty minimal...2 YEAR OLD TIRES WTF does this car ever get driven??? replace them there old or do a good burnout on the rear that should sticky them up a bit :(

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

pineapples work well in reducing any rear cradle movement...which helps eliminate axle tramp...also the likely hood of the shocks being gone in a car os this age should be pretty minimal...2 YEAR OLD TIRES WTF does this car ever get driven??? replace them there old or do a good burnout on the rear that should sticky them up a bit :(

yep... hehe

then again, i must say the lines are a far more advanced engine type for their age(r33) compared even to my B-series VTEC screamer. I mean, yeah, the lines have more torque and more upgrades.With VTEC,well,yeah, only so much u can do.

yep the car is not lowered.

well so far it happened on 1 roundabout cause i didn't want to try it again on another...

damnnnn

start Saving for a GTR.what do u think? Attesa kicks in and it is all sweet!

So it well could be just that one round-a-bout. There is one near my place, its like 40kmh in the dry and 10kmh in the wet its that bad.

My car isnt stock either, its going fairly hard coilovers, very hard sway bars, 2 way diff, blah blah blah.

So its just that round-a-bout or your shocks. Maybe your tyres as they are getting on a bit.

I woud say it is your tyres. ask a friendly sau member if maybe you coudld try out their set of wheels and you'll know.

trust me, tyres are the link between your car and the road. Suspensions etc blah blah can only do so much if you have old/dried or cheap tyres.

My car does that all the time too. In the dry too. But only because i purposely put my foot to the floor :D

I think its more than plausible for shocks to be shagged, its still a 9/10 year old car. My 95 has buggered shocks, probably the stupid hard jap springs dont help. In combination with the bad roads around here they didnt stand a chance.

I have had the rear end step out in a straight line under acceleration, purely because the shocks are so bad.

all this tyre pressure talk won't make much of a different with road tyres.

Maybe 1 or 2 psi would not make much of a difference but I can tell you for a fact that it pressure can make a decent difference. My daily driver Pulsar was running 26psi all round at one stage (bit low), and I pumped it up to 36psi front and 32psi rear. The difference in turn-in and handling in gereneral is like the difference between night and day.

As for whether this could cause the problems described. Well it's hard to say. It is possible that an overinflated tyre will only contact the road directly in the middle of the tyre. The lower pressure will also help the sidewalls flex more, hense maximising the road contact.

May sound stupid, but it may be worth first checking that the wheels are rotating in the correct direction, as these tyres are directional.

u said there was light drizzle, there may have also been sum oil/grease on the road, and as u said, about 3000rpm, ur just startin to make boost. there may be nothin rong with the car (shocks or tires). i was in a 34 gt-t a few weeks back, completely stock (still had stock exhaust and airbox in place) and with the traction control on, it would still step out in second, on a damp road, about 3000rpm, what happened to u sounds pretty normal IMO

Maybe 1 or 2 psi would not make much of a difference but I can tell you for a fact that it pressure can make a decent difference. My daily driver Pulsar was running 26psi all round at one stage (bit low), and I pumped it up to 36psi front and 32psi rear. The difference in turn-in and handling in gereneral is like the difference between night and day.

As for whether this could cause the problems described. Well it's hard to say. It is possible that an overinflated tyre will only contact the road directly in the middle of the tyre. The lower pressure will also help the sidewalls flex more, hense maximising the road contact.

May sound stupid, but it may be worth first checking that the wheels are rotating in the correct direction, as these tyres are directional.

i used to run the whole car with 32 psi but of the last 2 months i put 39 psi up front and 34.5psi rear.

tonite, i have put 32 psi on the rear and 34 psi up front. Went back to that god damned roundabt and in fact floored the car there. Nothing...

<u>slight conclusion to those following this thread</u>

2 factors : could have been either air pressure on tyres OR just the bloody road/roundabout was plain slippery when wet(drizzling).

u said there was light drizzle, there may have also been sum oil/grease on the road, and as u said, about 3000rpm, ur just startin to make boost. there may be nothin rong with the car (shocks or tires). i was in a 34 gt-t a few weeks back, completely stock (still had stock exhaust and airbox in place) and with the traction control on, it would still step out in second, on a damp road, about 3000rpm, what happened to u sounds pretty normal IMO

dude,

would R33s have traction control as an option???

its just practice... especially in the wet... I used to think my car oversteered badly until I got better at driving the thing (was made worse with lowered harder springs and the stock worn shocks)... now I have the suspension sorted I have the rear swaybar on full hard and the front on medium as 33s tend to understeer hard when pushed into a tight corner and I HATE understeer!

I also have the pineapples (set to max traction) and they really enable you to feel the road through the chassis and have more confidence in what the rear end is doing... before the pineapples the rear end was all vague and mushy... note I also had the bilsteins from the group buy go in at the same time so the improvement was significant but I can't tell what improvement the pineapples had by themselves

firstly, what you explained sounds like fun i dont know why you are complaining.

secondly, just after it drizzles a little bit the road becomes VERY slippery as oil comes to the surface of the road and is not washed away yet. so you probably got caught in that extry slippery time :woot:

dude i will try that :woot:

as i recall the skylines are to run higher pressure on front tyres because of the engine putting more weight on the car... any thoughts?

easy - 32psi for all 4 wheels..

mate, 39psi is crazy, thats too much

what's pineapples doiing in a skyline? LOL. Seriously, what are they?

They come as part of SK's suspension package - very worthwhile. Ive got em, as I love my pinapples.

At the end of the day, either 2 things

a) tyres (condition, ie green rubber, ie its gone off, or pressure is off, either too low or too high, I say too high)

b) suspension

Probably both of the above. Tyres have silica content, this aids grip, as you do more kms you wear your tyres more (and at 39psi you're wearing them out fast, as thats too high), and as you wear the tyres more you have less silica, which means less grip. Sort-of, generally speaking. Add in the greasy oil on the road from drizzle, and yes it gets sliperrrrrry

Plus Id bet my left nut your shocks are weaping and are GONE.

Edited by Tangles
I think i know the problem.......

http://www.skylinesaustralia.com/forums/in...howtopic=116233

could be serious.........

Too much power?

Hahaha, "Amatuers dont use nitrous oxide.... i've seen the way you drive, you got a heavy foot!"

:D

Maybe 1 or 2 psi would not make much of a difference but I can tell you for a fact that it pressure can make a decent difference. My daily driver Pulsar was running 26psi all round at one stage (bit low), and I pumped it up to 36psi front and 32psi rear. The difference in turn-in and handling in gereneral is like the difference between night and day.

As for whether this could cause the problems described. Well it's hard to say. It is possible that an overinflated tyre will only contact the road directly in the middle of the tyre. The lower pressure will also help the sidewalls flex more, hense maximising the road contact.

May sound stupid, but it may be worth first checking that the wheels are rotating in the correct direction, as these tyres are directional.

i agree with what you say about the way the tyres hold the road at diff pressures and i have experienced the differences also but unless this guy is running less than ~25 psi or above 40psi i don't think the pressure is the problem here.

easy - 32psi for all 4 wheels..

mate, 39psi is crazy, thats too much

Murcotts disagrees with you. i was aprehensive when they told me to come to their 2nd course with 40psi in the tyres. i can't remember exactly what they said to justify it but i think it was to do with having them inflated so that the water channels are effective.

guys

it was drizzlin' a little yesterday. Was driving the car and as i exited the round-a-bout, i gently tapped the accelerator. Now,the bloody tail just slipped .I am getting annoyed with this cause i am only doing like 20km/h.

What do you think is bloody wrong?

running very good tyres on the ride (Bridgestone Potenza Re01s all four) with 70% tread.

HELP!

Wet conditions are unpredible mate especally if it has not rained in a while all the oil and greese comes to the surface making it very slippery. I always take it very easy arround town in the wet conditions.

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...