Jump to content
SAU Community

Recommended Posts

HAHAHAHA, well my impression was he drove like a knob...

The white RX7 had speed all over him in the first session and yet he pulled accross the straight to block out the RX going into turn one...

Then had the Rx all over his bumper for the rest of the lap until he decided to let him pass buy loosing control and go onto the dirt :devil:

That yellow 33, for all it's slicks and poop was an absolute piece of junk. Way too low to handle properly and very poorly presented but what a wanker. He was trying to take up about 4 car spaces along the pit exit and trying to force everyone to go right out around his spot by an extra car length so he could just drive along and put it on blocks so he could install yet more cable ties to hold it together. Not surprised he was too arrogant to get out of the way to let a faster car through and cracked under the pressure.

Pretty sure thats the one from www.secretdrift.com.au He has a build thread in "drift projects'. Pretty budget/back yard.

You guys looked like you were having a ball, I thought i wont take the SS cause it will be too slow...

But then i saw the 6 litre Calais smasing everything in his group... And it looked like it was running stock tires and everything...

There was also a few SS utes there also doing quite well for stock as a rock... I was quite impressed as to how fast they were in compairison to the serious cars...

So maybe the SS can round the circuit in an ok time??

wasnt me brother, i didnt make that one! (was stuck at work, i remeber it clearly caus i spat the dummy caus i had to do overtime that nite :devil:)

have u f**ken taken ur car to allstar??????????????

Benji went to that day perhaps you have been mistaken for Benji Shane

Hows work shane???

Where the car currentlly at, got it started yet?

Gonna be a lakeside on Saturday?

f**k look at the time, i better go to bed long day tomorrow... Cya

works good mang :devil:

car's currently at micks awaiting some love (cage n chassis work) i've bene spending all my monies on these billet goodies, so nothings bene spent on the gtr for quite awhile

i was there in the arvo, missed u obviously

lakeside looked great this morning... :thumbsup:

Saw Geoff bashing up the track and saw Chris waving a flag or two...

Watched a blue wrx take a corner too hot and end up flipping 180 degres right in front of the integra...

The VE Calais 6 litre auto was going nuts, was really supprised how weel it went up against the GTR's...

Watched the yellow R33 being pressured by the white RX7 to the point where the R33 left the track and was very lucky not to smack the wall...

Was allot of speed coming down onto the straight out of that last corner, the track is faster than i can remember... :)

Cant wait to see the picks... Also does anyone know the contact details for the track as I was speaking with one of the maintainance guys and they have a skidpan up the back of the circuit, so maby we can go to skidpan here and save a 2 hour drive to Gympie???

Guilty as charged.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...